617896
33
Zoom out
Zoom in
Previous page
1/76
Next page
TASCAM DP-03SD 33
6 – Basic Recording
Selecting the input sources
This unit has two inputs (INPUT A and INPUT B) that can be
selected separately as input sources.
The input sources that can be selected with the INPUT A and
INPUT B switches include the built-in mics (MIC A and MIC B)
on the front panel or connected devices input through INPUT
A and INPUT B on the rear panel. In addition to mic and line
signals, the INPUT A standard jack can accept guitar input. Set
the INPUT A switch to GUITAR to input a guitar.
INPUT A INPUT B
GUITAR
Use when
connecting a guitar
or bass directly to
the standard INPUT
A jack
MIC/LINE
INPUT A jack (XLR
or standard jack)
INPUT B jack (XLR
or standard jack)
INTERNAL MIC A/B Built-in mic (MIC A) Built-in mic (MIC B)
NOTE
Do not connect to both the XLR connector and the standard
jack of an input (INPUT A or INPUT B) at the same time.
TIP
When connecting an electric-acoustic guitar with a built-
in preamp or an active electric guitar, as well as when
connecting an electric guitar with an effect pedal between it
and this unit, set the INPUT A switch to MIC/LINE.
Using phantom power
When connecting a condenser microphone that requires
phantom power, follow the procedures below to turn phantom
power ON. When phantom power is ON, phantom power is
provided to the XLR jacks of both INPUT A and INPUT B.
1 When the recorder is stopped, press the PHANTOM button
to open the
PHANTOM
screen.
2 Press the F4 (
ON
) button to turn phantom power ON. The
indicator above the PHANTOM button lights, and the Home
Screen reopens.
To turn phantom power OFF, press the F1 (
OFF
) button
instead.
The following screen appears whenever phantom power is
being turned ON or OFF.
NOTE
The screen above appears when phantom power is being
turned ON or OFF. No other operations can be conducted
while this message is shown. Other operations will be
possible after this message disappears and the Home Screen
reopens.
CAUTION
Turn the master fader down before turning phantom power
ON or OFF. Depending on the mic, a loud noise could occur,
damaging equipment and harming people’s hearing.
Do not connect or disconnect a mic when phantom power is
ON. This could cause a loud noise and damage equipment.
Turn phantom power ON only when using a condenser
microphone that requires phantom power.
Do not supply phantom power to an unbalanced dynamic
microphone. Doing so could break it.
Supplying phantom power to some types of ribbon
microphones could break them. Do not supply phantom
power to a ribbon microphone if you are in doubt.
Monitoring input signals
To monitor an input signal press the REC button for the track set
to record that signal. That tracks REC indicator will light/blink.
NOTE
When the unit is playing back, both the playback signal
and the input source signals are mixed and output through
the PHONES and LINE OUT jacks and can be heard with
connected headphones and monitoring systems.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam DP-03SD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam DP-03SD in the language / languages: English as an attachment in your email.

The manual is 6,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info