617901
18
Zoom out
Zoom in
Previous page
1/64
Next page
18
TASCAM DA-6400/DA-6400dp
3 – Preparation
NOTE
During installation, be careful not to tighten the screw too
much.
Connecting and disconnecting USB
flash drives
You can connect and disconnect USB flash drives whether the
unit is on or off.
CAUTION
Do not disconnect a USB flash drive when it is being
accessed in one of the following manners.
Doing so could damage data or the USB flash drive.
Moreover, disconnecting the USB flash drive during the
execution of a firmware update could result in the unit
becoming unable to start up or operate properly.
i During execution of the
FACTORY PRESET
function
i During execution of a
SYSTEM BACKUP
IMPORT or
EXPORT
i During execution of a firmware update
i When the
BROWSE
screen is open and the USB flash
drive is being accessed
Installing I/O cards (sold separately)
CAUTION
Before installing or removing an I/O card (sold separately),
disconnect the power cord from the outlet or the unit.
1. Remove the two screws from the plain panel and remove
the panel itself. (If a different card is already installed,
remove it.)
2. Insert the I/O card into the card slot. Align the edges of the
I/O card with the white guides inside the slot and insert it
securely. Push the I/O card in until its backplate reaches the
back panel of the unit, leaving no gap, and clicks into place.
Do not force the card into the slot. If you cannot insert the
card properly, remove it once and try reinserting it.
3. Use the two removed screws to secure the I/O card in place.
4. Turn the unit on, and check the
VERSION INFOR-
MATION
screen to confirm that it has recognized the
inserted I/O card. (See “Checking the firmware version on
page 51.)
If “SLOT1 : ---- (None)” or something similar appears, the card
might not be inserted correctly or the screws might not be
tightened securely. Insert the I/O card securely into the unit
again.
Turning the unit on and off (putting it
in standby)
When the unit is off, press the STANDBY/ON switch on the front
of the unit to turn it on.
DA-6400dp startup screen
Home Screen
After the unit starts and the startup screen is shown, the Home
Screen will open.
If no SSD/HDD is loaded in the slot or there are no audio files in
the current folder, the take number and time will not be shown
on the Home Screen.
8
Turning the unit off:
Press and hold the STANDBY/ON switch to open a pop-up
message.
When the confirmation pop-up is open, press and hold the
MULTI JOG dial to turn the unit off.
CAUTION
Do not turn the unit off (put it into standby) during
recording, playback or at other times when data on the
SSD/HDD is being accessed. The SSD/HDD case indicator
blinks orange at such times. Doing so could cause proper
recording to fail, recorded data to be lost, and sudden loud
noises from monitoring equipment, which might damage
the equipment or harm hearing.
When the unit is started up for the first time (or when the
built-in clock is reset after being left unused without power
for a long time), the
CLOCK ADJUST
screen appears
after the start-up screen to allow the date and time of the
built-in clock to be set. (See “Setting the built-in clock date
and time” on page 19.)
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam DA-6400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam DA-6400 in the language / languages: English as an attachment in your email.

The manual is 1,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info