587266
24
Zoom out
Zoom in
Previous page
1/28
Next page
24 TASCAM CG-1800/CG-1000
8 – Other functions
Setting the startup preset
You can set the preset used at startup when this unit is turned
on. Make this setting on the
UTILITY 1
page.
1. Press the MENU button to open the
UTILITY 1
menu
page, and turn the MULTI JOG dial to select the
STARTUP
item.
2. Press the MULTI JOG dial to open the
STARTUP MODE
screen.
3. Turn the MULTI JOG dial to set the preset used at startup.
Option Function
LAST (default) Startup with last used settings
PRESET 1
Startup with the corresponding preset
settings
PRESET 2
PRESET 3
PRESET 4
FACTORY Startup with factory default settings
NOTE
The
STARTUP
item setting cannot be restored to the
factory default.
4. Press the MULTI JOG dial to confirm the selection and return
to the menu.
Calibrating the internal oscillator
The importance of calibration
This unit has an OCXO (oven-controlled crystal oscillator) that
provides 0.01ppm high-precision frequency output. However,
every clock generator, including this one, can normally be
expected to change over time.
In order to enable continued use with high-performance, this
unit has a function for calibrating the internal oscillator.
If you connect and input a 10MHz signal generated from
a GPS signal or a PPS signal, for example, to the dedicated
CALIBRATION INPUT
connector, the unit will recognize it
automatically and calibrate the internal clock.
Checking the unit firmware version
Follow these procedures to check this unit’s firmware version.
Do this before updating the firmware, for example.
1. Press the MENU button repeatedly to open the
UTILITY
2
menu page, and turn the MULTI JOG dial to select the
VERSION
item.
2. Press the MULTI JOG dial to open the
VERSION
screen.
The
VERSION
screen shows information about the
firmware version and build number.
3. Press the EXIT/CANCEL button to return to the menu
screen.
NOTE
When the
VERSION
screen is open during step 2 above,
press the MULTI JOG dial to switch to firmware updating.
For the latest information about updating firmware, visit
the TEAC Global Site (http://teac-global.com/).
Checking the error log
Follow these procedures to check the error log, which contains
information about past errors.
Check the error log from the
LOG
page.
1. Press the MENU button repeatedly to open the
LOG
page
menu, and turn the MULTI JOG dial to select the
ERROR
LOG
item.
2. Press the MULTI JOG dial to open the
ERROR LOG
screen.
In the error log, each error is shown on a separate page.
Error log page example
1 Error log number
These numbers are assigned to errors in order as they are
added to the log.
2 Error date and time
This shows when the error was added to the log.
3 Error summary
This shows the error code and signal affected as described
in the Overview of error codes table. (See “Overview of error
codes” on page 10.)
4 Signal that error affected
This shows the signal that the error affected.
5 Error result
This shows what happened because of the error.
6 Recovery date and time
This shows when the unit recovered from the error.
7 Recovery summary
This shows how the unit recovered from the error.
8 Recovery result
This shows what happened when the unit recovered.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tascam CG-1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tascam CG-1000 in the language / languages: English as an attachment in your email.

The manual is 0,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Tascam CG-1000

Tascam CG-1000 User Manual - English - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info