Manual SureFlap Microchip Pet Door (page 15 of 265) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish)

782758

Zoom out

Zoom in

1/265

7.5 Installation in walls

Before you install the Microchip Pet Door in the wall of your home please consult a

qualied builder about the best location. Remember that there may be electrical

wires, gas or water pipes hidden within the wall which if damaged during the

installation can cause serious problems.

For installation of the Microchip Pet Door in a wall we recommend that you use SureFlap Pet

Door Tunnel Extenders (Product Code: TUN101).

Choose your mounting position on the wall ensuring that your pet will have easy access

through the Pet Door in both directions.

1. Measure the height of your pet’s stomach from the oor when your pet is standing. This

height is the level at which the bottom of the hole should be cut through the wall. Make a

mark on the wall at this height. Note: If there is a large drop on the outside of the house

you will need to place a step outside for your pet to access the tunnel.

2. Take the external frame as you will need to use this as a template to mark the hole in

the wall. Firstly make a small pencil mark at the bottom of the external frame in the

centre – see gure 20.

3. Put a piece of Blu-tack or similar low tack putty on the four corners of the frame. See

gure 21.

4. Stick the external frame to the wall on the inside of the house, lining up the pencil mark

and bottom of the frame with the mark you have made on the wall. Use a spirit level to

ensure that the frame is level. See gure 22.

5. Using a pen or pencil draw around the inside of the frame on the wall so you have a

clearly visible cutting line. You can now remove the frame from the wall.

6. Before you start to cut the hole through the wall remove the Pet Door from the area to

minimise the amount of dust and debris the product is subjected to.

7. We do not recommend that you cut through the inside and the outside surface of the

wall in one go – cut the hole on the inside of the house rst and then move outside to

cut the hole there. You may want to drill one hole straight through the wall in the centre

of the tunnel as a guide.

8. Whether you are cutting through brick, wood, tiles or plaster you should drill some pilot

holes rst around the perimeter of the line you have drawn. These holes should go

slightly over the line by no more than 1 or 2mm (1/16”). Then remove all of the material

in the centre using the most suitable tools for the material you are cutting. See gure 23.

9. It is important not to make the hole too large or you will not be able to screw the Pet

Door to the wall .

10. Once you have made the hole on the inside of the house you can move to cutting the

hole on the outside of the house. Remember to make the hole on the outside of the

house slightly lower than the inside so that rain can run out of the tunnel. Clear away

any dust and debris from inside the hole

11. Fix the tunnel extenders together and to the end of the Pet Door tunnel using an

All-Weather adhesive tape. Do not use glue in case you have to make adjustments or

remove the Pet Door – see gure 24.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of SureFlap Microchip Pet Door in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7.16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

SureFlap Microchip Pet Door Manual

Product: