464692

Sunwave SRC-7000 Manual

14
Zoom out
Zoom in
Previous page
1/75
Next page
SRC-7000
Touch Screen Smart Remote Control
User’s Manual
041201
Preface
i
Preface
About this manual
This manual is designed to make using the SRC-7000 Smart Remote Control as
easy as possible. Information in this document has been carefully checked for
accuracy and is subject to change without notice.
Copyright
© Copyright 2005
This document is protected by the international copyright law. No part of this
publication may be reproduced by any means without the permission of
SUNWAVE Technology Corporation in Taiwan.
The information provided from SUNWAVE Technology Corporation is believed to
be accurate. Any changes and enhancements to the product and to the
information thereof will be documented and issued as a new release to this
manual.
Trademarks
Other product names mentioned in this manual are used for identification purposes
only. All trademarks and registered trademarks are the property of their respective
owners.
1
Table of Contents
Preface ................................................................................... i
Table of Contents ................................................................. 1
Chapter 1 Introduction to the SRC-7000............................ 4
1.1 SRC-7000 Features....................................................... 5
1.2 Unpacking the SRC-7000............................................. 5
1.3 Battery Installation ....................................................... 6
1.3.1 Battery Precautions.............................................................................7
1.4 Turning the Touch Screen On ..................................... 7
1.5 Identifying Components .............................................. 8
1.5.1 Top of SRC-7000.................................................................................8
1.5.2 Botton of SRC-7000............................................................................9
1.5.3 Direct Access Buttons ( Rubber Keys) ..............................................10
1.5.4 LCD Touch Screen............................................................................ 11
1.5.5 Precautions When Using the Touch Screen...................................... 11
1.5.6 Touch Screen Keys ...........................................................................12
Chapter 2 Quick Start ....................................................... 17
2.1 Re-calibrating the Screen.......................................... 17
2.2 Date / Time Setting ..................................................... 18
2.3 Device Setting............................................................. 19
2
Chapter 3 How to Set Up Your SRC-7000........................ 21
3.1 Add a Device............................................................... 21
3.1.1 Create a New Device ........................................................................ 21
3.1.2 Load the Codes for the Newly-added Device.................................... 23
A. Pre-code....................................................................................................... 23
B. Learning........................................................................................................ 25
3.2 Add a Soft Key............................................................ 27
3.3 Adding Text ................................................................. 29
3.4 Re-label a Device, Key or Text .................................. 30
3.5 Re-size a Device, Key or Text.................................... 32
3.6 Delete a Device, Key or Text...................................... 33
3.7 Pre-programmed Code .............................................. 35
3.8 Learning ...................................................................... 37
3.9 Learn a Cycle Key ...................................................... 40
3.10 Delete Device / Key Codes ...................................... 41
3.11 Create a Macro.......................................................... 42
3.11.1 Macro ..............................................................................................42
3.11.2 Timer Macro ....................................................................................45
A. Create a Timer Macro.................................................................................. 45
B. Delete Your Timer Macro.............................................................................47
C. Re-label Your Timer Macro..........................................................................48
D. View Your Timer Macro ............................................................................... 49
3.12 Set Up Your Favorite Channels............................... 50
3.12.1 Add Favorite Channel Keys............................................................. 50
3.12.2 Set Your Favorite Channels as Macros...........................................51
3
Chapter 4 Menus ............................................................... 52
4.1 Set Up the Remote ..................................................... 52
4.2 Key Layout .................................................................. 56
4.3 Code Setting ............................................................... 57
4.4 Timer Macro ................................................................ 58
4.5 Duplicate ..................................................................... 59
Chapter 5 Install USB Cable and Software ..................... 61
5.1 Introduce SLC-2080 USB Cable ................................ 61
5.1.1 Install the SLC-2080 USB Driver.......................................................61
5.2 Install Upgrade Tools................................................. 63
5.3 Upgrade VMCU Firmware and VMCF Pre-
programmed Codes ......................................................... 66
Appendix A ......................................................................... 69
Features ............................................................................ 69
Specifications ................................................................... 70
Appendix B ......................................................................... 71
Optional Accessories....................................................... 71
Appendix C ......................................................................... 72
Troubleshooting Tables ................................................... 72
4
Chapter 1 Introduction to the
SRC-7000
Congratulations on purchasing SRC-7000 Smart Remote Control
(SRC-7000). The SRC-7000 is a digital Universal Remote Control with
smart design that is easy to configure and use, enabling you to control
all your IR equipped electronic devices.
One of the main features is the touch screen control panel, which can
integrate a number of remote controls in one and reduce the number of
buttons for each device. The design makes it easy for you to find the
function you want. You can control up to 64 devices by 8 default
categories such as TV, Satellite, VCR, DVD/VCD, Amplifier/Receiver,
CD/MD, Tuner/Tape and AUX.
This remote features very simple setup, combining both
preprogrammed codes and learning ability, you can easily configure
each device at home or office. The unit features high compatibility with
over 95% of brands available in the market. Furthermore, you can also
easily edit devices, change the LCD appearance, and customize other
settings.
Macro and Timer functions enable you to initiate a chain of 60
commands just by tapping a key. Also, the Macro combined with the
timer can operate automatically at specific times.
The SRC-7000 offers superior flexibility over most brands combined
with preprogrammed codes offering ease of operation. With the SRC-
7000, you are able to add or delete devices, re-label devices or keys,
and change the size and shape of the LCD soft keys. You can control
all your devices with one remote control. No longer will you have to
search for several different remotes!
Chapter 1 Introduction to the SRC-7000
5
1.1 SRC-7000 Features
This following list identifies SRC-7000 key features. For more
information on getting the most, please refer to the following
chapters.
1. Control up to 64 devices including VCD/DVD, TV, Satellite,
VCR, CD/MD, Receiver/Tuner, Tape, etc.
2. Large LCD touch-screen display with automatic backlighting for
visibility in low light environments.
3. Direct access buttons for accessing frequently used functions
such as volume, channel, play, mute and stop.
4. Excellent learning ability with auto learning guide
5. Huge pre-programmed codes database.
6. Motion detector enables users to power up remotes
automatically.
7. Fully customizable keys, devices, icons and layouts.
8. Each macro can store up to 60 commands with time delays.
9. Inbuilt timer enables Macros to operate automatically.
10. With the optional SDS-7000 Docking Station, users can charge
Ni-MH rechargeable batteries.
11. On-line upgradeable by the Upgrade Tools and editable by the
RemoteComm software.
1.2 Unpacking the SRC-7000
After unpacking the package, please make sure the following items
are included.
SRC-7000 Smart Remote Control x 1 set
User’s Manual with pre-programmed code list x 1 set
If any of above items is missing or appears damaged, please
contact your local dealer immediately. Do not throw the shipping
package away in case you need to ship your SRC-7000.
For the optional accessories, you can contact your local retailers
directly.
SRC-7000 User’s Manual
6
1.3 Battery Installation
Please refer to the following illustration and instructions for inserting
the batteries
1. Remove
battery
cover.
2. Insert batteries.
Ensure
that you
insert
the batteries
according to
the marking
inside the
battery case.
Figure 1-1: Inserting the batteries
The battery compartment is located at the back of SRC-7000.
1. Put your thumb in the battery cover slot and pull to remove the
cover.
2. Insert new batteries into the bay in the direction indicated in
the battery compartment.
3. Replace the battery bay cover. You will hear it click into place.
Chapter 1 Introduction to the SRC-7000
7
1.3.1 Battery Precautions
Please pay attention to the following instructions:
1. Be sure that the positive (+) and negative (-) polarities of each
battery match the polarities indicated in the compartment.
2. Do not expose the batteries to excessive heat or flame.
3. Keep the batteries away from children.
4. Low power batteries will reduce the effective distance of the
unit.
5. Do not mix different type of batteries or mix new and used
batteries at the same time.
If you use Ni-MH rechargeable batteries, please pay
attention to the following.
a. Before the first use, please charge the batteries for 10
hours.
b. Do not recharge the batteries with an unqualified
charger.
c. When the battery low warning icon appears, please
recharge batteries right away.
d. Please renew the batteries immediately if the running
time is lower than half of the running time of a new fully
charged battery.
Warning:
When the battery low warning icon appears, you
may not enter the Setup Menu to operate the functions
such as using learning function, adding a Macro, or
deleting devices.
1.4 Turning the Touch Screen On
Figure 1-2: Turning the LCD on
There are three ways to turn on
SRC-7000:
1. Picking up the SRC-7000. The
motion detector design will turn
the SRC-7000 on.
2. Pressing any rubber key.
3. Tapping the LCD touch screen.
SRC-7000 User’s Manual
8
1.5 Identifying Components
Please refer to the following illustrations to identify the components
of SRC-7000. This section provides you an overview of the SRC-
7000. For the detailed description on operation, please refer to
Chapter 3.
1.5.1 Top of SRC-7000
Figure 1-3: Front view
1. Light sensor (P.54)
The Light Sensor will detect
the ambient brightness to
control the backlight whether
turn on or not.
2. Touch screen LCD (P.12)
The LCD screen enables you
to configure and control your
devices by tapping the screen.
In addition, you can tap the
screen to power on SRC-7000.
3. Hard key (P.10)
You can operate the most
frequently used functions by
pressing these hard keys.
4. Transmission port (P.71)
With the port, you can connect
your PC to the SRC-7000 with
the SLC-2080 USB cable to
upgrade the MCU firmware or
edit the SRC-7000.
Chapter 1 Introduction to the SRC-7000
9
1.5.2 Botton of SRC-7000
Figure 1-4: Rear view
1. IR port
This needs to be pointed to the IR
receiver of the targeted device.
2. Reset switch
You can reset the SRC-7000 when
the SRC-7000 does not work
properly or hangs up (freezes).
3. Rear label
The rear label marks the model
number and the brief specifications.
4. Buzzer opening
Beep tone signals are transmitted
through here.
5. Battery compartment
Contains the 3xAAA Alkaline
batteries or Ni-MH rechargeable
batteries.
6. Learning eye (P.37)
The SRC-7000 learns the IR codes
from the original device through
this learning eye. Simply point the
original device to SRC-7000this
learning eye 2~4 inch apart and
press corresponded key on the
original device, and save the
corresponding code into the SRC-
7000.
In this way, SRC-7000 will learn the
IR codes from your original device.
SRC-7000 User’s Manual
10
1.5.3 Direct Access Buttons ( Rubber Keys)
The Direct Access Buttons provide you with easy access to often-
used functions such as volume, channel control, skip to the next,
skip to the previous, reverse, play and stop… etc. Before use,
these functions must be set. (Refer to Chapter 3: How to Set Your
SRC-7000, Page21.)
Figure 1-5: Direct access buttons
These direct access buttons functions as follows in set up and normal use:
Setup mode function Device normal function
n
● Enter the setup menu by pressing it for
about 2 seconds.
● Exit the setup item and back to last setup
mode.
● Back to the Main menu
o
● Enter the submenu
● Confirm the setup item
● Turns on the backlight
p
● Select the items ● Channel up or channel down button
● Play or Stop function
q
● Change the degree of the selected item. ● Volume up or volume down
● Skip to the next or Skip to the previous
r
● No function ● Device power button: Press the button to
turn on the selected device
s
● No function ● Mute function
● Open the disk/ tape
* These buttons function differently according
to the currently selected device.
Chapter 1 Introduction to the SRC-7000
11
1.5.4 LCD Touch Screen
The LCD (Liquid Crystal Display) touch screen enables you to
configure and operate your SRC-7000 with the touch of a finger.
1.5.5 Precautions When Using the Touch Screen
Please pay attention to the following instructions to avoid damaging
your SRC-7000.
1. Do not tap hard on the LCD touch screen. Tap the LCD touch
screen gently.
2. Do not use a pen or any sharp object to tap the screen.
3. Do not immerse it in liquid. Keep the Remote dry. Wipe off any
spills immediately because SRC-7000 is not waterproof.
4. Do not expose SRC-7000 to extreme temperatures. Keep it
away from heat sources.
5. Do not drop the SRC-7000.
6. Do not put anything on the touch screen.
7. Do not use abrasives or cleaning solutions to clean SRC-7000. If
necessary, dampen a clean soft cloth slightly with clean water
before cleaning.
SRC-7000 User’s Manual
12
1.5.6 Touch Screen Keys
The touch screen keys enable you to control your devices as you
would do with your original remote control. You can also set up
macros, program timers, cycle keys and configure the LCD screens
as you want.
Figure 1-6: Touch screen buttons
It is very easy to use the touch screen. You just need to tap the soft
buttons to activate the specific function. Before use, you have to set
up the SRC-7000. (Refer to Chapter 3 How to Set Your SRC-7000,
Page 21.)
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sunwave SRC-7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sunwave SRC-7000 in the language / languages: English as an attachment in your email.

The manual is 2,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info