704206
35
Zoom out
Zoom in
Previous page
1/52
Next page
80-0067-00-MO-RevJ 2019-01-30 SunTech CT40 User Manual | 35
The Memory Delete icon and Check icon will flash in sync with the Selection Knob. All other values on the
screen will be blank.
Press the Selection Knob again to delete all measurements or rotate the knob clockwise until the X icon flashes
and press the Selection Knob to cancel the deletion.
EMR Transmissions
Section 4 covers the basics of sending measurements to EMR. Here are more details.
Validating Patient ID with EMR
Scan the patient’s barcode ID with your barcode scanner. If your SunTech CT40 is connected to an EMR, a verification
query will automatically be sent to the EMR to confirm the validity of the patient ID. If the EMR responds that the
patient ID is valid, then the patient ID icon, field values and Check Icon will flash four times.
If the EMR responds that the Patient ID is invalid, then the Patient icon field, field values and X icon will flash six times
and a message will appear in the Patient ID field indicating that the Patient ID entered is not valid.
NOTE: The Patient ID must be validated by the EMR before any vital signs measurements can be sent to the EMR.
Sending Measurements to EMR
Sending measurements to an EMR will work only if your SunTech CT40 has been configured to connect to an EMR.
After scanning a valid Patient ID, and taking vital signs measurements, press the Memory Button . The EMR
icon and Check Mark Icon will start flashing. Press the Selection Knob to send the data to the EMR. If
the measurements are delivered to the EMR successfully, you will see the EMR Message Icon and the Check
Mark Icon flash four times.
If the EMR has a problem receiving the measurements, the EMR Message icon and X icon will flash eight
times and you will hear 4 short beeps. You will see a message indicating the nature of the problem, such as:
“Rejected” or “Rejected for an error.” This message occurs when the device is connected to the network but the EMR
rejects the message. A corresponding message will appear in the Patient ID field during a three-second period when
the Message Icon and X icon flash on and off.
“No response (time out).” This message occurs when the device is connected to the network but the EMR is not
responding. It also can occur if network connectivity is lost. If there is a network connection, the SunTech CT40 will
continue to try to transmit the message every 10 seconds. A message in the Patient ID field will alert you that another
attempt to send the message will be made in 10 seconds. If network connectivity is lost, you will see a corresponding
message in the Patient ID field, and the device will continue trying to reestablish a connection and send the
measurements at intervals set during EMR setup. If problems persist, you may wish to contact your facility’s
information technology department. As a backup, the patient’s measurements are saved in the device memory when
the memory button was pressed and can be retrieved using the procedure detailed in the beginning of Section 9.
Note: After the memory button is pressed, all values to be stored to memory will flash off and on twice, along with the
check mark icon, memory icon and memory location identifier. After flashing, the display will revert to null values for the
patient ID and all measurement data, and the check mark icon will flash off and on twice more.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for SunTech CT40 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of SunTech CT40 in the language / languages: English as an attachment in your email.

The manual is 2,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of SunTech CT40

SunTech CT40 User Manual - German - 49 pages

SunTech CT40 User Manual - Dutch - 52 pages

SunTech CT40 User Manual - French - 50 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info