654315
31
Zoom out
Zoom in
Previous page
1/44
Next page
Care and cleaning
The coffee making process involves extracting
oils out of coffee grinds to make espresso
coffee. Deposits of these oils build up over
time and affect the taste of the coffee and
operation of the espresso machine.
Regular cleaning to remove these oils is
essential and will maintain the quality of the
coffee the espresso machine produces and
result in less maintenance being required.
This is easy to do by following a few quick
and easy cleaning steps after each coffee
making session;
Cycle water through the group head,
Purge steam through the steam wand,
Wipe the steam wand clean with a damp
cloth immediately after use,
Remove the filter basket from the filter
handle and clean away any old coffee oils,
and
Empty the drip tray and rinse.
Important: Never wash any of the espresso
machine parts or accessories in the
dishwasher.
Drip tray and grill
Remove the grill and drip tray at regular
intervals to empty (45) (46). Clean with
water and a little non-abrasive washing up
liquid, rinse and dry.
Group head, group handle & filter baskets
The filter baskets and group handle should
be rinsed with warm water after each use and
then dried thoroughly.
To clean the group head of any old coffee
grinds cycle water through and wipe the
group head and around the inside rim with a
damp cloth.
Should the holes in the filter baskets become
clogged with coffee grinds use a fine bristled
brush to remove them. Also you can use
the cleaning pin which is supplied with
the espresso machine. The cleaning pin is
attached to the cleaning disk, located on the
inside of the back door (49). The cleaning
pin has two pins at either end - one is
labelled 'FILTER' and is the shorter of the
two and is for cleaning out the holes in the
filter basket.
Note: When cleaning the dual-floor filters
be sure to check the single hole on the
underside of the filter.
Group head rubber seal
The group head seal is located on the
underside of the group head and creates
a seal against the filter handle during the
espresso pour.
Note: During long periods of non-use we
recommend that the filter handle not be
left attached to the group head as this will
reduce the life of the seal.
Over time the seal will loose its elasticity
and require replacement, depending on use
usually every 12 months. Signs that the seal
is deteriorating are when the group handle
cannot create the necessary seal and steam
and or water escapes from around the group
head during the espresso pour. Another sign
may be when the group handle locks off to
the right rather than the front.
Note: Contact Sunbeam on 1800 025 059
should you think that the group head seal
needs replacing. Please do not attempt to
change the seal without first consulting
Sunbeam.
Cup warming plate, hot water wand and exterior
Wipe over the unit with a damp cloth and
wipe dry. Do not use abrasives or metal
scourers as these will scratch the exterior
surface.
29
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sunbeam EM6910 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sunbeam EM6910 in the language / languages: English as an attachment in your email.

The manual is 5,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info