750861
17
Zoom out
Zoom in
Previous page
1/28
Next page
13
English
English
Antenna Type:
For a fixed dish, with a single LNB, select Fixed-LNBOnly (Default)
For a fixed dish set up, with more than 1 LNB, but max. 4 LNBs, including a DiSEqC 1.0 switch, select Fixed-
DiSEqC 1.0. If selected here, then select the corresponding ports at DiSEqC 1.0 below.
For the use of a SCR system (SatCR, Satellite Single Cable distribution) select SCR and then select the
corresponding User Band in the User Band and User Frequency options below.
For a Motor-driver dish set-up, using a DiSEqC 1.2 motor, select DiSEqC 1.2.
With DiSEqC 1.2 it is necessary to search and store every satellite position manually. This is very cumbersome
(and old fashion) to do so. Select a position (1 to 63) with Go To for a satellite and then with Move drive the
antenna until the satellite is found and optimise reception. Then store the position and satellite with Save
Position. Proceed for the next satellite.
GoToX is the unofficial successor to DiSEqC 1.2, sometimes called DiSEqC 1.3 Modern Motor-drives
are all DiSEqC 1.3 type. It involves a predefined satellite list and corresponding positions
to those satellites, in the receiver and a algorithm to determine where the satellite is, given
its geographical location. Only need is to enter the geographical location where the dish is
installed. All satellites can now be found automatically. If GoToX is selected, set the location
in the options below. At Satellite chose the satellite of your choice.
Satellite: Select a satellite to be configured.
LNB Power: Set the LNB power On or Off.
LNB Type: Select the LNB type. The Universal LNB (09750/10600 MHz) is supported and is the most
common on the market for European Ku-band use. Standard refers to C-Band LNBs, Wide C
refers to wide band C-band LNBs.
LNB Freq: Set the frequency of the selected LNB type.
Default is 9750/10600. The Universal LNB (09750/10600 MHz) is the most common on the
market for European Ku-band use.
It is also possible to select alternative frequencies for Universal LNB types.
Transponder: Select one of the available transponders of the chosen satellites in order to check your
reception or to align the antenna.
Move: To drive the antenna until the satellite is found and optimise reception
Sat Degree: Satellite position.
Ant Position: To enter the geographical position of the dish.
Go To: To make the dish move to the set position.
The following 2 options will only show when at Antenna Type the Fixed DiSEqC 1.0 option is selected.
22KHz Tone: Switch the 22 KHz oscillator signal to ON (22K) or OFF (0). Only for C-Band LNB use. Refer to
manual of LNB.
DiSEqC 1.0: Select the correct port of the corresponding LNB.
Available options: Off, Port A, …, Port D.
The following 2 options will only show when at Antenna Type the SCR option is selected.
User Band Select the User Band you are assigned to in the SCR system. Max. 8 users.
User Frequency Displays the corresponding Frequency for the User Bands. If the User Frequency does not
correspondent with any of the default User Bands for you particular SCR LNB, press OK and
select User Define and enter the correct User Frequency for the correct User Band. Then
press OK again.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT7840 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT7840 in the language / languages: English as an attachment in your email.

The manual is 3,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Strong SRT7840

Strong SRT7840 User Manual - Italian - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info