480577
13
Zoom out
Zoom in
Previous page
1/40
Next page
12 www.strongsat.com
Installation
Switching on for the first time
When you connect your set-top box to the mains, your set-top box’s front panel
lights go through a start-up sequence. After about 20 seconds, your set-top box is
switched on and out of standby, and the standby light is green.
Make sure your TV is switched on.
If the Countries screen below displays, your
TV is ready for digital satellite channels.
You can now continue the installation by
turning to the section ‘Making the installation
settings’ on page 13, but note that if you
have a VCR connected to your set-top box
via an RF lead, to be able to record satellite
programmes, you may need to perform RF
Tuning for your VCR - see below.
If the Countries screen does not display...
If you have connected your set-top box to your TV (and VCR) via SCART leads, try
selecting your TV’s ‘AV input’.
If you have connected your set-top box to your TV (and VCR) via RF leads only, you
need to tune a ‘channel for satellite TV’ (see below).
RF Tuning
If you have connected up your equipment via RF leads, you may need to perform RF
tuning before you can watch digital satellite TV.
Note
If you have previously had an analogue satellite receiver connected to your TV (and/or VCR), you
may find that your ‘channel for satellite TV’ still works for your new digital channels. Try it to see
- if it works you do not need to perform RF tuning.
RF tuning your TV (and VCR) to your set-top box
1. Make sure your set-top box is out of standby (the standby light on the front
panel should be green).
2. Consulting your TV’s user guide if necessary, tune the TV until you can see the
Countries screen (see above) on your TV screen.
3. Store your new ‘channel for digital satellite TV’ on a TV channel number of your
choice. For example, if your terrestrial channels are channels 1 to 5, and your
‘VCR channel’ is channel 8, you may wish to use TV channel 9 as your ‘channel
for digital satellite TV’.
4. If you have a VCR, set your TV to its ‘VCR channel’, then tune your VCR until
you can again see the Countries screen.
If you cannot RF tune your TV (or VCR) to your set-top box...
Your set-top box’s factory preset RF output channel is channel 38. (This is not the
same as a TV channel.)
u
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT6752 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT6752 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info