424993
18
Zoom out
Zoom in
Previous page
1/31
Next page
PART 1 • English
17
English
To add channel press YELLOW (Save) or BLUE (Save&Exit) button. The new channel will be added to the
list with name “Video CH XXXX”, where XXXX is equal to PCR PID (Video) you have entered.
5.2.1.1 Positioner setup
If in Dish setup menu you have configured Dish mode as “DiSEqC 1.2” then you have to setup position
of the dish to each satellite that you want to install.
In Channel setup menu move menu focus to Dish position item and press OK button on remote control.
Menu Positioner setup will appear on screen.
n Satellite: Displays the name of satellite position of antenna for which you setup
n Transponder: Use tu buttons to select reference transponder, receivable in your location, to
measure signal strength and quality
n Movement speed: Use tu buttons to select between Slow and Fast. Slow speed allows you to
fine adjust position of the dish (each press to direction button will turn dish
to short angle). Fast speed can be used to adjust dish position roughly. If
Movement speed set to Fast press to direction button will couse continuous
movement of the dish to appropriated direction, to stop dish you will have to
press OK button.
n Move: Use tu buttons to move dish to the East/West direction
n Centre position: If you press OK button while menu focus is on this item then dish will be
turned to centre position, which corresponds to true South direction.
n Limits: Use tu buttons to Enable or Disable software limits of your positioner.
n Set limit: Use tu buttons to select East or West limit of dish movement range.
Step by step recommendations of position setup.
n Select reference transponder in order to check signal strength and quality during position setup.
n If you do not know current direction of your dish then move menu focus to Centre position
item and press OK. Dish will be turned to true South. Knowing your location longitude you
may understand direction where necessary to move dish in order to reach position of selected
satellite. For example: your longitude is 5° East and you want to setup dish position for Astra 1C,
1E (19° East). Then, from centre position, you need to move dish to East direction by pressing to
t button. If your longitude is 25° East then, in order to setup dish position for Astra 1C, 1E (19°
East), you need to move dish in West direction (from centre position) by pressing to u button.
n To setup roughly position of the dish set Movement speed to Fast. Then move menu focus
to Move item of the menu and by short presses to t or u buttons move dish to necessary
direction. Check signal strength and quality indicators. Once levels start increasing – press OK
button to stop the dish. Set Movement speed to Slow and keep adjusting dish position until get
best possible values.
n Once you are sure that dish is fine adjusted press YELLOW (Store) or BLUE (Store & Exit) button.
Dish position for selected satellite will be stored.
NOTE: in order to avoid mechanical damage of your dish please, make sure those mechanical
limits in your motor are set correctly and dish would not hit any objects on its movement.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong srt 8345 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong srt 8345 in the language / languages: English as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Strong srt 8345

Strong srt 8345 User Manual - German - 35 pages

Strong srt 8345 User Manual - French - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info