480565

Strong SRT 8200 Manual

16
Zoom out
Zoom in
Previous page
1/23
Next page
13
English
6.3.5 Parental Control
After selecting this menu and pressing OK you will be asked to enter the PIN code DEFAULT PIN: 0000.
This menu allows you to use the EPG based parental rating system, given this is supported by the local
broadcast.
Age: Use t/u to change these settings. Following rates are available: OFF (to
disable the function), 04, 05, 06, 07, 08, 09, 10, 11, 12, 13, 14, 15, 16, 17 and 18.
Whenever switching through channels which submit EPG based parental rate
and the rate of the current broadcast is below the adjusted rate, you will have
to enter your PIN code.
EXAMPLE: Your youngest child is 7 years old, so you have adjusted a rate of 07. You are switching
to a channel which is not foreseen for an age below 10 years, so at this channel you will
have to enter the PIN code DEFAULT PIN: 0000.
6.3.6 Reset Factory Default
This option allows you to reset the receiver to the factory settings, which clears all stored channels and
settings.
WARNING: By resetting your receiver to the factory default, all your settings and stored channels
will be permanently deleted. Please use this option with care
After selecting this menu item and pressing OK you will be asked to enter the PIN code DEFAULT PIN:
0000. After you have performed this action you will be guided to the Installation Guide again!
If necessary, you can change the PIN code. To change the PIN code, please enter the Tools menu, see
chapter 6.4.3 of this manual.
6.4 Tools
Press MENU and use t/u to select Tools then press OK. Following submenus will be displayed: Timers,
Information, Change Password, USB Upgrade, OAD Upgrade and Remove USB device.
Use p/q to select a submenu and press OK or u to access.
6.4.1 Timer
The timer function allows you to turn the receiver on and off according to the defined settings. Timers can be
set from the EPG in the most convenient way but you can also set timers manually through this menu.
In the menu Schedule, a summary of the configured timers will be displayed: number, channel name,
date, start and end time, repeat and timer status.
NOTE: If no timers have been configured, the list will be empty.
You can add, change or delete a timer.
Add: To add a timer, press the RED button. In the new opened menu use t/u p/q
and 09 to configure the settings for the event. After the settings have been made,
set the necessary parameters and press OK to apply the timer into the list.
Channel Type: Use t/u to select between TV and radio programmes (the radio option is not
available if there are no radio channels broadcasted/in the channel list).
Channel No.: Use t/u to select the channel number to which you want to switch.
Channel Name: Here the channel name will be shown according to the channel number in above.
Start Date: Use 09 to enter the date on which the timer should switch the receiver on.
Please consider the date format “dd/mm/yyyy.”
Start Time: Use 09 to enter the start time.
End Time: Use 09 to enter the end time.
Repeat: Use t/u to select in which cycle the timer should be repeated. Once - the
timer will switch ON once, after this the setting will be removed from timer list.
Daily - the timer will switch ON every day at the desired time. Weekly - the timer
will switch ON once a week at the desired time.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 8200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 8200 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info