480565
8
Zoom out
Zoom in
Previous page
1/23
Next page
5
English
WARNING: The batteries should not be recharged, disassembled, electrically short-circuited, be
mixed or used with other types of batteries.
If rechargeable accumulators instead of batteries are going to be used, we recommend using (e.g. NiMH)
types with low self-discharge to ensure long time operation of remote control.
2.5 Using the remote control
Fig. 5
To use the remote control, point it towards the front of your receiver. The remote control supports a
range of up to 7 meters distance to the receiver at an angle of up to approx. +-30 degrees.
NOTE: Managing the receiver will be limited or not possible if there are obstacles between the remote
control sensor (at the front panel of the receiver) and the remote control. Direct sunlight or very
bright light can reduce or disturb the reception of the remote control signals.
3.0 CONNECTIONS
WARNING: Please make sure that connection devices are disconnected from their main power
supplies before connecting these to the receiver.
3.1 Connecting to your aerial antenna
Fig. 6
To receive digital broadcasted signals, your receiver has to be connected to a terrestrial indoor or
outdoor antenna. Use the antenna cable to connect the aerial with the ANT IN connector on the back of
your receiver. Please ensure that a properly shielded antenna cable and suitable connectors are used.
The TO TV connector allows you to loop the antenna signal to a second receiver or TV set.
3.2 Connecting to TV with HDMI cable
Fig. 6
We recommend connecting your TV set with the receiver using a good quality HDMI 1.3 or higher cable
(not included). This connection supports the highest possible quality.
3.3 Connecting to TV with a cinch cable
Fig. 6
Your receiver is also equipped with Audio L, R and VIDEO connectors. As an alternative, use these connections
if your TV set doesn’t have an HDMI connector. Use a cinch cable to establish the connection.
3.4 Connecting to a digital audio amplifier
Fig. 6
By connecting your receiver to a digital amplifier or home theatre system, you can enjoy the best possible
sound quality and multi-channel audio (depending on broadcast). Connect your Digital Audio Amplifier or
home theatre system with a suitable cable to the S/PDIF connector on the back of the receiver.
3.5 Connecting to a digital A/V receiver and TV using HDMI
Fig. 7
By connecting your receiver to an A/V receiver or enhanced digital home theatre system with HDMI, you
will enjoy the best possible sound and picture quality as well as multi-channel audio too (depending
on broadcast). Connect the HDMI output of the receiver to the corresponding input of your A/V system
and then connect the HDMI output of the A/V receiver or home theatre system to your TV set. Select the
correct input on your A/V system to watch and listen to programmes. If your TV set already supports DD
audio we recommend you to use the direct connection as described above in chapter 3.2.
3.6 Connecting an external USB storage device
Fig. 6
NOTE: For details to consider when using a USB storage device please refer to chapter 1.5.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 8200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 8200 in the language / languages: English as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info