568531
12
Zoom out
Zoom in
Previous page
1/17
Next page
9
PART 1 • English
English
Channel Lock: OFF/ON. If set to ON”, select channels to be locked in the TV or radio channel editorpage.
Parental Lock: No Block/Total Block/05/06/07/08/09/10/11/12/ 13/14/15/16/17/18. Age restriction
information to programmes can be transmitted by thebroadcaster.
NOTE: If any of the above mentioned items are set to ON, then you need a valid PIN to gain access
to the Parental Control menuagain.
Change Password: The default is “NO”, when you press tu, you are asked to enter the old password rst (the
default password is ”0000”).
9.3 Update
9.3.1 ImageUpgrade
Enter the Others menu, select ImageUpgrade, then press OK. Press pqtu to select the desired item, then
highlight Start and press OK to start upgrade. Press EXIT toexit.
You can upgrade the software version via OTA or by a software image, obtained from the STRONG website, to
be used with a USB device. Preferably use an empty USB device formatted in FAT32, such as a Pen drive, only
containing the image in theroot.
If an image is obtained from the STRONG website www.strong.tv, you must unzip the le rst on a PC and only
transfer the *.ssu le onto the USB device. Detailed instructions are also given on thewebsite.
When in the upgrade page, use pqtu to select the image le and press OK to start the upgrade process. A
progress bar will be shown and after a successful upgrade, the unit will reboot and show the initial Installation
page. From here you can re-install thechannels.
NOTE: Do not power the unit down or pull the mains plug during upgrade. Do not try to load any
other software than for this unit issued by the STRONG website www.strong.tv. Advisedly, do
not connect or disconnect any cables during upgrading. Trying to load any other software
might destroy the unit, but certainly void yourwarranty.
NOTE: If your unit should unexpectedly behave erratically after a software update, please perform
a factory reset. See 9.4 Factory Setting. For software upgrade it is possible to use a USB pen
drive or aHDD.
9.3.2 OTA Over TheAir’
The unit is capable of receiving and processing OTAupgrades.
OTA updates are not always available from all networkproviders.
For details check the STRONG website www.strong.tv.
9.4 FactorySetting
This menu allows you to re-set the receiver back to factory settings and clear all existing channels. In the Others
menu, select Factory Setting and press OK. A valid Pin must be entered. Then a conrmation window is displayed.
Select the O to return back to factory settings and clear all channels. Select the X button to cancel. Press EXIT
toexit.
The unit will reboot and display the rst Installationscreen.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 80 in the language / languages: English as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info