480579
10
Zoom out
Zoom in
Previous page
1/15
Next page
7
PART 1 • English
English
DiSEqC: If your antenna is connected through a DiSEqC switch and you have already executed the First Installation
with mySAT search then this setup is already according your installation. You only need to specify the
DiSEqC input in case it has been wrong configured or the installation setup has changed. Use the tu
buttons to select the correct setting, press OK to confirm.
GOTO X settings: Here you can setup your location in order to use GOTO X type of Positioner.
Motor: If you use a motorised dish (DiSEqC 1.2 or DiSEqC 1.3) set DiSEqC1.2 or GOTO X, if not then set to
Disable by using the tu buttons.
nDiSEqcC1.2
Almost same like GOTO X, but without function of go to position X. For settings please see
below description.
nGOTO X:
Set motor to GOTO X and press OK to enter the menu to adjust the direction of the dish
pointing to the selected satellite.
Position Auto: Press tu buttons, the dish will be moved to West/East continuously, it will stop until itnds the best
signal.
Move dish: Press tu buttons, the dish will be moved to West/East to search the best signal, release the button will
stop the moving.
Fine Tuning: Set thene tuning, for optimised adjustment.
Move step: Move to East or West stepwise.
Limit set: Disable or enable West or East limit, for mechanical limit.
NOTE: In order to avoid mechanical damage of your dish please, make sure those mechanical limits in your motor are
set correctly and dish would not hit any objects on its movement.
Store position: Press OK button to save the current position you searched.
Go to position: Press OK button to move the dish to the stored position.
Go to Reference: Press OK button to move the dish to 0.0 >reference position.
Go to X.X: Press OK button to move the dish to exact position of the satellite
FTA only: Use the tu buttons to select YES if you want to search only for Free-To-Air channels and NO if you want
to search for scrambled channels as well.
Start Search: Use the tu buttons to select the scan mode for Transponder, Satellite or Advanced Scan.
5.1.2 Edit Satellite data
Dependent on the focus you set with the tu buttons you can edit a satellite or its transponder data. Select a satellite or
transponder with the pq buttons and press OK to enter the menu, then PIN-code (default: 0000) is requested.
In case you have chosen satellite, the following possibilities are available: Rename, Delete, Move, Add.
Rename: Now you can use the tu and pq buttons to choose characters from the shown keyboard, press OK to
insert. Press GREEN (Back) button to delete character and use the RED (OK) button to confirm the new
name.
Delete: This will delete the selected satellite. A message will appear, press OK if you want to delete the satellite or
EXIT to cancel.
Move: Here you can move the position of the selected satellite in the satellite list. Use the numeric buttons to
enter new position.
Add: Use the numeric buttons to enter orbital position of the new satellite and tu to select between East or
West.
In case you have chosen transponder these possibilities are available: Delete, Edit, Add.
Delete: This will delete the selected transponder.
Edit: Use the numeric buttons to enter the new value for the selected Frequency and Symbol rate and use the
tu buttons to select the correct Polarisation and FEC.
Add: Like described above, but this will add a new transponder.
5.1.3 Remove Satellite
Here you can remove an installed satellite from the list. Use the pq buttons to select the satellite you want to remove, press
OK to enter the menu, then PIN-code (default: 0000) is requested. After entering the PIN-code the satellite is marked with X
to delete. You can select other satellites to remove or press EXIT. You will be asked for confirmation to delete (OK) or cancel
(EXIT).
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 6511 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 6511 in the language / languages: English as an attachment in your email.

The manual is 1,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info