813456
29
Zoom out
Zoom in
Previous page
1/40
Next page
29
Maintenance & Servicing
3. Fitting a new Door Glass
3.1 To maintain the safe use of your appliance you may need to
replace a damaged door glass.
3.2 Using the appliance with a damaged door glass could cause
dangerous fumes to enter the room, or the appliance to
over-fire, resulting in damage.
3.3 A new door glass and installation instructions (PM484) are
available from your retailer.
4. Fitting a new Door Seal
To maintain the safe use of your appliance you need to
replace damaged or worn door sealing rope.
To do this:
4.1 Remove the door from the appliance, by opening the door
and lifting the door free of the hinge blocks on the left hand
side of the door.
4.2 Lay the door face down on a soft flat surface, to protect the
paintwork and glass.
4.3 Remove the old rope and scrape old glue from the locating
groove.
4.4 Clean the locating groove with a clean dry cloth to remove
all old dust and debris.
4.5 Squeeze a generous bead of fresh Stovax Thermic Seal
glue into the rope locating groove.
4.6 Press the new Stovax rope into the locating groove, placing
the joint in the middle of the lower edge of the door,
see Diagram 1.
Rope
Channel
Ø13mm Door
Sealing Rope
Rope joint
1
4.7 Refit the door and close the door to apply pressure to the
new rope.
4.8 Leave the door(s) closed for at least 12 hours before
lighting the appliance and run at a low temperature for
approximately one day. This allows the adhesive to fully
bond to the seal.
4.9 Using the appliance with a damaged door seal can cause
dangerous fumes to enter the room, or the appliance to over
fire, resulting in damage.
5. Adjusting the Door Hinges
5.1 To maintain the safe use of your appliance, you may need to
adjust the door hinges to ensure the door closes safely and
correctly.
The door can be adjusted in 2 different places:
5a Door Hinge Pin Assembly.
5b Hinge Blocks on Firebox.
5a. Door Hinge Pin Assembly
To adjust the Door Hinge pin assembly:
5a.1 Remove the door from the appliance, by opening the door
and lifting the door free of the hinge blocks on the left hand
side of the door.
5a.2 Lay the door face down on a soft flat surface, to protect the
paintwork and glass.
5a.3 Use the hinge pin assembly on the back of the door to
adjust the position of the door in relation to the appliance.
Hinge pin
Assembly
M6 Dome
Nuts x4
2
5a.4 Use a 10mm A/F spanner to loosen the 4 M6 dome nuts.
The hinge pin assembly is slotted so it can be adjusted up
or down and sideways approximately 3mm.
5a.5 Once the desired position has been achieved ensure the
dome nuts are firmly tightened against the hinge block
assembly to maintain the position.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stovax Riva Vision - Wood Freestanding Stove at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stovax Riva Vision - Wood Freestanding Stove in the language / languages: English as an attachment in your email.

The manual is 4.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info