537132
93
Zoom out
Zoom in
Previous page
1/122
Next page
92 MS 240, MS 260, MS 260 C
High speed screw
: Screw the puller (1) 5910 890
4500 counterclockwise into the
limiter cap – left-hand thread.
: Rotate the limiter cap until the lug
(2) is in line with the slot (1).
: Pull out the limiter cap (1).
Take out the high speed
screw (H).
Always install a new limiter cap.
1
165RA368 TG
165RA369 TG
1
2
1
165RA370 TG
: Inspect the tip (arrow) for
damage or wear and replace the
screw (H) if necessary.
Screw down the high speed
screw (H) as far as stop.
Continue with installing limiter
cap.
Pre-installing limiter cap
: Push the new limiter cap (1) on to
the high speed screw (H) as far
as the detent (arrow)
– do not push it fully home.
The basic setting with the pre-
installed limiter cap is carried out
with screwdriver
5910 890 2304.
Reassemble in the reverse
sequence.
Carry out basic setting, b 14.5.1
165RA371 TG
165RA372 TG
1
14.5 Adjusting the Carburetor
14.5.1 Basic Setting
The basic setting is necessary only
if the high speed screw (H) or low
speed screw (L) has to be replaced
or after cleaning and adjusting the
carburetor from scratch.
It is necessary to carry out the basic
setting after removing the limiter
cap.
The carburetor and air filter are
installed, the adjusting screws fitted
and the new limiter cap pre-
installed.
Check chain tension and adjust if
necessary.
Inspect the spark arresting
screen (if fitted) and clean or
replace if necessary. b 8.1
Check the air filter and clean or
replace if necessary, b 14.1
Starting with the low speed and
high speed screws against their
seats, turn them 1 full turn
counterclockwise.
Allow engine to warm up.
Setting disk 5910 893 6600 may be
fitted on the screwdriver
5910 890 2305 to simplify
adjustments.
93


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl MS 240 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl MS 240 in the language / languages: English as an attachment in your email.

The manual is 4,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stihl MS 240

Stihl MS 240 User Manual - German, Dutch, French, Italian - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info