537132
36
Zoom out
Zoom in
Previous page
1/122
Next page
35MS 240, MS 260, MS 260 C
8.3 Oil Seals
It is not necessary to disassemble
the engine to replace the oil seals.
Ignition side
Remove the fan housing,
b 10.2
Remove the flywheel, b 9.5
Remove the generator, b 15.7
Versions with handle hearing
: Remove the Woodruff key (1).
Free off the oil seal in its seat by
tapping it with a suitable tube or a
punch.
: Apply puller (1) 5910 890 4400
with No. 3.1 jaws 0000 893 3706.
165RA106 TG
1
165RA107 TG
1
Clamp the puller arms.
Pull out the oil seal.
Take care not to damage the
crankshaft stub.
Clean the sealing face with a little
standard solvent-based
degreasant containing no
chlorinated or halogenated
hydrocarbons.
Lubricate sealing lips of new oil
seal with grease, b 17
Apply a thin coating of sealant to
the outside diameter of the oil
seal (1), b 17
Slip the oil seal (1), open side
facing the crankcase, over the
crankshaft stub.
: Use press sleeve (2)
1121 893 2400 to install the oil
seal (1).
The seating face must be flat and
free from burrs.
Wait about one minute, then
rotate the crankshaft several
times.
Clean the crankshaft with a little
standard commercial solvent-based
degreasant containing no
chlorinated or halogenated
hydrocarbons.
165RA108 TG
1
2
: Install the Woodruff key (1) – its
straight side (arrow) must be in
line with the taper.
Reassemble all other parts in the
reverse sequence.
Clutch side
Remove the sprocket cover and
cutting attachment, b 5
Remove the clutch, b 6
Remove the oil pump,
adjustable, b 13.5,
non-adjustable, b 13.4
: Remove the washer (1) and
ring (2).
165RA109 TG
1
165RA110 TG
1
2
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl MS 240 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl MS 240 in the language / languages: English as an attachment in your email.

The manual is 4,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stihl MS 240

Stihl MS 240 User Manual - German, Dutch, French, Italian - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info