667200
66
Zoom out
Zoom in
Previous page
1/280
Next page
HTA 65, HTA 85
English
64
Cutting effortlessly with a correctly
sharpened chain
A properly sharpened chain slices
through wood effortlessly and requires
very little feed pressure.
Working with a dull or damaged chain
requires more physical effort, exposes
the user to higher vibration levels,
produces unsatisfactory cutting results
and increases wear.
N Move the retaining latch to ƒ.
N Remove the battery.
N Clean the chain.
N Check the chain for cracks in the
links and damaged rivets.
N If such cracks or damage are found,
remove the chain and replace any
worn parts of the chain. Match the
new parts to the shape and size of
the original parts.
WARNING
It is absolutely essential to comply with
the angles and dimensions specified
below. If the saw chain is incorrectly
sharpened and in particular if the depth
gauge is set too low – there is an
increased risk of kickback, with resulting
risk of loss of control and injury.
Chain pitch
The chain pitch (a) is marked on the
depth gauge end of each cutter.
Select file diameter according to chain
pitch – see table “Sharpening Tools”.
You must observe certain angles when
resharpening the chain cutter.
Filing and side plate angles
A Filing angle
B Side plate angle
The specified angles A and B are
obtained automatically if the
recommended files or sharpening tools
and correct settings are used.
The angles must be the same on all
cutters. If the angles are uneven: The
chain will run roughly, not in a straight
line, wear quickly and finally break.
File holder
Always use the proper tools. Sufficient
and constant practice will make
sharpening easier.
N Use a file holder
A file holder (special accessory) must be
used for manual resharpening (see table
"Sharpening Tools" at the end of this
chapter). The correct filing angles are
marked on the file holder.
Use only special saw chain sharpening
files. Other files have the wrong shape
and cut.
Maintaining and Sharpening
the Saw Chain
Mark (a)Chain pitch
inch mm
71/4P6.35
Chain type Angle (°)
AB
Picco Micro (PM) 30 75
689BA027 KN
a
Cutter shapes
Micro = Semi-chisel
66


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl HTA 65 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl HTA 65 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 14,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info