466729
24
Zoom out
Zoom in
Previous page
1/56
Next page
First, cut a large, wide felling notch.
Make a plunge cut in the center of the
notch.
The plunge cut is made with the guide
bar nose. Begin the plunge cut by
applying the lower portion of the guide
bar nose to the tree at an angle. Cut until
the depth of the kerf is about the same as
the width of the guide bar. Next, align
the saw in the direction in which the
recess is to be cut.
With the saw at full throttle, insert the
guide bar in the trunk.
Enlarge the plunge cut as shown in
illustration.
:DUQLQJ
There is an extreme danger of kickback
at this point. Extra caution must be taken
to maintain control of the saw. To make
the felling cut, follow the sectioning
method described previously.
If you are inexperienced with a chainsaw,
plunge-cutting should not be attempted.
Seek the help of a professional.
/LPELQJ
Limbing is removing the branches from
a fallen tree.
:DUQLQJ
There is an extreme danger of kickback
during the limbing operation. Do not
work with the nose of the bar. Be extremely
cautious and avoid contacting the log or
other limbs with the nose of the guide bar.
Do not stand on a log while limbing it
you may slip or the log may roll.
Start limbing by leaving the lower limbs to
support the log off the ground. When
underbucking freely hanging limbs,
a pinch may result or the limb may fall,
causing loss of control. If a pinch occurs,
stop the engine and remove the saw,
by lifting the limb.
:DUQLQJ
Be extremely cautious when cutting
limbs or logs under tension (spring poles).
The limbs or logs could spring back
toward the operator and cause loss of
control of the saw and severe or fatal
injury to the operator.
%XFNLQJ
Bucking is cutting a log into sections.
:DUQLQJV
1. When bucking, do not stand on the
log. Make sure the log will not roll
downhill. If on a slope, stand on the
uphill side of the log.
Watch out for rolling logs.
001BA033 L
Ä
001BA089 L
Ä

24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl 026 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl 026 in the language / languages: English as an attachment in your email.

The manual is 1,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stihl 026

Stihl 026 User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info