Manual Stiga VILLA SILENT - 2010 (page 52 of 164) (All languages)

564032

Zoom out

Zoom in

1/164

ENGLISH

The battery must be fully charged

before being used for the first time. The

battery must always be stored fully

charged. If the battery is stored while

discharged, serious damage will occur.

5.8.1 Charging with the engine

The battery can be charged using the engine’s

generator as follows:

1. Install the battery in the machine as shown

below.

2. Place the machine outdoors or install an

extraction device for the exhaust fumes.

3. Start the engine according to the instructions in

the user guide.

4. Allow the engine to run continuously for 45

minutes.

5. Stop the engine. The battery will now be fully

charged.

5.8.2 Charging using battery charger

When charging using a battery charger, a battery

charger with constant voltage must be used.

Contact your dealer to purchase a battery charger

with constant voltage.

The battery can be damaged if a standard type

battery charger is used.

5.8.3 Removal/Installation

The battery is placed under the engine casing. See

fig. 13. During removal/installation of the battery,

the following applies regarding connection of the

cables:

• During removal. First disconnect the black

cable from the battery’s negative terminal (-).

Then disconnect the red cable from the battery’s

positive terminal (-).

• During installation. First connect the red cable

to the battery’s positive terminal (+). Then

connect the black cable to the battery’s negative

terminal (-).

If the cables are disconnected/

connected in the wrong order, there is a

risk of a short-circuit and damage to the

battery.

If the cables are interchanged, the

generator and the battery will be

damaged.

Tighten the cables securely. Loose

cables can cause a fire.

The engine must never be driven with

the battery disconnected. There is a risk

of serious damage to the generator and

the electrical system.

5.8.4 Cleaning

If the battery terminals are coated with oxide, they

should be cleaned. Clean the battery terminals with

a wire brush and lubricate them with terminal

grease.

5.9 AIR FILTER

The pre-filter (foam filter) must be cleaned/

replaced after 25 hours of operation.

The air filter (paper filter) must be cleaned/

replaced after 100 hours of operation.

NOTE! The filters should be cleaned/replaced

more often if the machine operates on dusty

ground.

Remove/install the air filters as follows.

12, 12 HST, 14 HST:

1. Remove the protective cover of the air filter

(14:R).

2. Dismantle the paper filter insert (14:S) and the

foam pre-filter (14:R). Make sure that no dirt

gets into the carburettor. Clean the air filter

housing.

3. Clean the paper filter by tapping it gently

against a flat surface. If the filter is very dirty,

replace it.

4. Clean the pre-filter. If the filter is very dirty,

replace it.

5. Assemble in the reverse order.

Silent:

1. Dismantle the air filter cover (9:R) by undoing

its screw.

2. Dismantle the filters. The pre-filter (9:B) is

placed over the air filter (9:A). Make sure that

no dirt gets into the carburettor. Clean the air fil-

ter housing.

3. Wash the pre-filter in liquid detergent and wa-

ter. Squeeze dry. Pour a little oil on the filter and

squeeze in the oil.

5. Assemble in the reverse order.

Compressed air or petroleum-based solvents such

as kerosene may not be used for cleaning the paper

filter insert. This will damage the filter.

Do not use compressed air for cleaning the paper

filter insert. The paper filter insert must not be

oiled.

5.10 SPARK PLUG

The spark plug(s) must be replaced every 200

hours of operation (=at every other basic service).

Use the spark plug key supplied.

Before disconnecting the spark plug, clean around

its mounting.

Spark plug

: Champion RC12YC or equivalent..

Electrode distance

: 0.75 mm.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga VILLA SILENT - 2010 in the language / languages: All languages as an attachment in your email.

The manual is 4,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiga VILLA SILENT - 2010 Manual

Product: