Manual Stiga SVP 40 B (page 27 of 96) (All languages)

608756

Zoom out

Zoom in

1/96

OPERATING INSTRUCTIONS

For the engine, read the relative instructions manual.

NOTE - The number which precedes each paragraph links

the references in the text to the respective illustrations

(listed on page 2 and following pages).

NOTE - The machine can be supplied with some parts

already assembled.

WARNING - Unpacking and completing the assembly

should be done on a flat and stable surface, with

enough space for moving the machine and its pack-

aging, always using suitable equipment.

Disposal of the packaging should be done in accor-

dance with the local regulations in force.

Assembling the handle

Lay the lower part (1) of the handle and the upper part (2)

on the ground.

Block the two parts (1) and (2) together using the knob (3).

Fix the lower part (1) to the supports (4) using the knob (5)

and screws supplied, following the sequence in the figure.

Remove the knob (6) and connect the terminal (7) to the

lever hole (8), using the same knob (6) and relative nut (9).

Move the rotor positioning lever (10) to «A» (work) and op-

erate the adjustment knob (11) till the point (12) touches

the lock (13).

NOTE – The meanings of the symbols on controls are

explained on page 6 and following.

Throttle control

The throttle is controlled by the lever (1).

Lever positions are indicated on the relevant plate.

The throttle regulates tine rotor rotation speed.

Rotor positioning control

The lever (1) allows you to position the tine rotor at two dif-

ferent heights:

«A» = Work

(with rotor tines in contact with the ground);

«B» = Transfer

(with the rotor raised to move the machine).

2. CONTROLS AND REGULATIONS

1. COMPLETE ASSEMBLY

2.2

2.1

1.1

The rotor must be disengaged when you move from one

position to the other.

Regulating depth

How deep rotor tines go into the ground can be regulated

by the specific knob (1):

– clockwise = reduces depth;

– anti-clockwise = increases depth.

Rotor engagement lever

You engage the rotor (with the engine running) by pushing

the lever (1) against the handle.

Releasing the lever (1), the rotor stops and the engine

stays running.

Starting the engine

For start up, follow the instructions in the engine manual,

then firmly pull the knob on the starter cable (2).

Aerating and scarifying the ground

When moving the machine, move the rotor positioning

lever to the «B» position ( 2.2).

Lift the stone-guard (1) and hook on the grass-catcher (2).

To begin working:

– move the rotor positioning lever to the «A» position

( 2.2);

– regulate depth ( 2.3);

– engage the rotor ( 2.4) and move the machine for-

ward.

Lawn care suggestions

• Over time, a layer of moss and grass residue forms on

the ground surface reducing its supply of oxygen and

stopping water and nutritious substances from pene-

trating. This impoverishes the lawn and makes it yellow.

• You can remove that surface felt with a surface aerating

action (with reduced tine depth in the ground).

• By increasing depth (scarifying), that removal action in-

volves the harder ground layer and, at the same time,

separates grass roots and increases them. This makes

your lawn thicker with more blades of grass.

2.3

3.1

3. USING THE MACHINE

2.4

3.2

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga SVP 40 B in the language / languages: All languages as an attachment in your email.

The manual is 1,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiga SVP 40 B Manual

Product: