9 - WARNING !! The petrol/gasoline is highly inammable: Don’t ll the tank neither in closed areas, nor when engine is on, don’t smoke and
be careful to the petrol/gasoline loss from the tank. In case of leak, don’t try to switch the engine on but move the machine away from the area
in order to avoid ignition source until the gasoline vapours fade away. Re-place the tank caps and the gasoline box.
10 - Keep attention to the exhaust pipe. The parts near the pipe can reach 80°C.
Replace the defective and/or worn out silencers Burn hazards !!!.
11- Don’t use the motor hoe on steep slopes: it could overturn!. On slope it is recommended to work crosswise, neither in slope nor in descent
and be vary careful during any change of direction.
12 - Before putting the machine into operations, check it visually and make sure all the accident prevention measures are working. It is
absolutely forbidden to exclude and/or to tamper with them. Replace worn or damaged elements.
13 - In case the machine is incorrectly used, and/or the repairs are performed by non-authorized technical staff, and/or tted by spare parts
other then original ones: any use other than that described above is prohibited and will involve the cancellation of the warranty and the refuse
all responsibility from the manufacturer.
SAFETY FEATURE (Fig. 14) All motor-hoes are provided with a safety feature which acts. The device causes the transmission to disconnect
automatically anytime the respective control levers are released (2 Forward speed – 3 Reverse speed).
NOTES ON HOW TO WORK WITH THE MOTOR-HOE With the engine running, rest the tines on the ground, and rmly holding the
motor-hoe, insert the spur into the soil. Lower the clutch lever on the handlebar to allow the disks to bite into the soil. The motor-hoe will move forwards
when the handlebars are used to slightly lift the disks. The spur arm must always remain in the soil during work. Uses: Light or medium textured soil
working. Soil working (hoeing/breaking-up). Soil tillage (weeding). Ploughing in compost or fertilizers, etc. Attention: The motor-hoe is unsuitable for
working in soils covered by thick grass/lawns. It is also unadvisable to use the implement on stony soils.
TRANSPORTA forklift truck should be used to move the machine. The forks should be opened as far as possible and inserted into the pallet. The
weight of the machine is given on the Manufacturer’s data plate together with the other technical information. Motor-hoe can be transported to given
place by means of transport wheel (Fig 14 part. 8). Switch off the engine before transporting the machine.
HOW TO ASSEMBLE YOUR MOTOR-HOEUnless otherwise agreed, the motor-hoe is delivered disassembled and placed in a packing
case. For assembly to be completed, the step by step procedure is as follows :
TRANSFER WHEEL (Fig. 2 A and 2 B) Take from the packing box the support wheel complete with wheel (1) and insert it in the front seat of the frame
(A). Fit the spring (2) and secure it with the washer (3) and the cotter pin (4) into the housing hole. The wheel support is in the transport position as
shown in Fig. 2A. To shift to work position pull it towards the wheel support (1) and turn it to the right until it stops. See g. 2 B. The spring, washer and
cotter pin can be found inside the bag accessories.
SPUR (Fig. 3) Insert the spur (1) in correspondence of the hole of the frame (A). Secure with washer (2) and with the R pin (3) you can nd in the
accessories bag.
HANDLEBAR ASSEMBLY ( Fig. 4) :To assemble the handlebar (1) on the tiller frame, perform the following steps:
In the upper hole to pass the screw (2) in the grommet (3) with already entered the control cables and then secure it with the nut (4). Use the lower slot
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Stiga SRC 750 G at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Stiga SRC 750 G in the language / languages: All languages as an attachment in your email.
The manual is 4,83 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
