608769
21
Zoom out
Zoom in
Previous page
1/128
Next page
11
ATTENTION! The used oil must not be drained into the sewer system or waterworks. In order to prevent any pollution to the water-table. Most garages
have used oil deposits, or use the authorized deposits according to your local authority regulations.
TRANSMISSION SCYTHING BAR (Fig. 12) there are 2 greasing point (1-2) . Important : after every use of the motor mower , please clean
and grease the scything bar and all motion parts/mechanisms.
ENGINE SERVICING ( please read the specic part). The motor mower is delivered equipped with a 4 stroke engine , NO OIL is included. Please
ll the tank in up to the shown level ( capacity about 0,5 kg.). Referring to the oil/viscosity type, please follow the engine producer instructions.
SERVICE - GARAGING : the motor mower is undoubted one of the most used agricultural equipment and need a good and frequent servicing.
We recommend you to clean the machine very deeply after every use. Keep attention that all the nuts , screws and bolts are tightened in order to
guarantee a good machine working on safety conditions. Leave the machine to cool before garaging anyhow don’t room it if the tank contains still
contains some fuel as the vapours could reach some blazes or sparks. To lower the re danger , keep the engine , the silencer and the fuel area free
from leaves, grass or greasy substances.
If the machine is not used for long periods it is essential to protect the blade and the bar using some anticorrosive and antioxidant materials. The
presence of impurities or foreign bodies on the meadow, damages the teeth sharpening of the scything bar. It is useful to sharpen the blade and check
the teeth integrity every 4-6 hours of use. Only if you keep a good sharpening teeth level you can obtain the best grass cut.
BLADE SHARPENING (Fig. 13) : according to the frequency and the type of use , the cutting sections have to be sharpened about every
10 hours working. To obtain a perfect sharpening you need to use and electric sharpening machine (15.000/20.000 turns/minute) , grinding-headed
with a diameter 25 mm and length 35 mm. The blade has to be sharpened from the internal part of the rod to tip.end section using the head grinding.
The blade sections have to be sharpened in a 25° deg. angle.
DESCRIPTION (Fig. 15) 1) Start-Stop operating lever - 2) Drive operating lever - 3) Cutter bar clutching control lever - 4) Engine - 5) Cutter
bar. 6) Cable-guide Bracket – 7) Cowling.
TECHNICAL DETAILS Track: 430 mm - Length of cutter bar: 660/870 mm - Total length: 1350 mm - Total height: 1050 mm - Tires: 2 tires 4.00-6
- Mass: 49/52 kg. MOTOR - Cooling: air cooling - Fuel tank: 0,75 Litre. Please consult the relative instruction manual for other technical information
and details about the engine.
ACCESSORIES: front mount snow blade cm. 85 and pair chains. For the assembly of the snow blade , tighten the pin in the ttings connection
seating and x it using a “R” pin.
EN
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga SILEX 87 B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga SILEX 87 B in the language / languages: All languages as an attachment in your email.

The manual is 1,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info