Put the throttle handle (1) on start position , then switch the engine on. Adjust the throttle lever in order to get to the needed engine revolutions.
To proceed with cutting operations, lower the red lever (3) and pull the hand driving level (2) for the forward speed.
In case you have to face an unforeseen and accidental obstacle, you should immediately leave the two driving levers (2 and 3). When you nished
your work, please switch the engine off, and put the throttle lever (1) on stop position.
SETTING THE HANDLEBAR HEIGHT (Fig. 17) Set the height of the handlebar according to the user’s height. The height is usually
adjusted to hip level.
• Loosen the screws (2).
• Set the height of the handlebars using the longitudinal holes (10).
• Retighten the screws (2).
CUTTER BAR HEIGHT ADJUSTMENT (Fig. 10) Having to mow on uneven soils, you must adjust the cutter bar height. Proceed as
follows : unloose nut (1), shift sliding block (2) in desired position, tighten nut (1). Perform this step on both sliding blocks. Both sliding blocks must
be set to the same height.
ADJUSTING THE KNIFE (Fig. 9) After the changing the blade and after 15 hours work it is necessary to adjust the blade holders (3).
Clean the cutting bar using a jet of water and overlap the teeth of the two blades.
Using the screws (1) and the nuts (4) eliminate the over-space between the teeth caused by the wear. Than disassemble the cover and verify the
bar movement to be free , by rotating the pulley (2). Hands must be protected by sturdy gloves.
N.B. for a correct adjustment of the blade , please go to a qualied service center.
ADJUSTING AND CONNECTION FOR THE SCYTHING BAR: (Fig. 7) to increase the belt tension between the unit and the
accessories , you should act on the adjusters (2) to make the bar to start scything only when the lever (4) has crossed half its way. ATTENTION !
before lowering the accessories insert lever (4) , you should always unhook the safety lever (3).
BELT-STRETCHER CONTROL ADJUSTMENT (Fig. 8) : attention ! the motor mower wheels should start to turn when the driving lever
(g. 7 part. 1) has crossed half its way. When the mentioned lever is completely pulled, i.e. on working position , the load-belt of the belt-stretcher (2)
should extend for 6-8 mm. To perform so you should act on the adjuster (3). To end the operation, tighten the nut on the adjuster (part. 5 g.7).
CUTTING BLADE REPLACEMENT (Fig. 16) Unscrew (1), take the blade coupling out (2) and then remove the blade. To reassemble the
blade, perform these operations backwards. Note - To achieve good cutting, blade must always be sharp.
GEARBOX (Fig. 11) : Check the gearbox oil level every 60 hours of work. Disassemble the right wheel and, keeping the unit on horizontal
position, unscrew the cap (1) placed on the side.
The oil level must be at the lower level of the lling hole. In case it is not lled in , please add SAE 80 oil type.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Stiga SILEX 87 B at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Stiga SILEX 87 B in the language / languages: All languages as an attachment in your email.
The manual is 1,81 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
