Manual Stiga Pro 740 IOX - P 901 PH (page 266 of 858) (All languages)

608703

266

Zoom out

Zoom in

1/858

ENGLISH

(Translation of the Original Instructions)

9.6 CHECKING/TOP-UP THE TRANSMIS-

SION FLUID

For the frequency of this intervention

see chapter 13.

For the type of oil to use please refer to “0 TECH-

.

9.6.1 Check / top-up (25)

1. Place the machine on a at surface.

2. Read the uid level in the reservoir (25:A).

The level should match the line.

3. Top up if necessary.

9.7 BELT DRIVES

check that all the belts are intact.

9.8 BATTERY

For the type of battery installed on the machine,

please refer to “0 

WARNING! Battery acid is corrosive

and contact with it is harmful. Handle

the battery with care taking care not to

let acid leak out.

        

comes into contact with eyes or skin. If

any part of the body comes into contact

with acid, rinse immediately with co-

pious amounts of water and seek medi-

cal attention immediately.

The battery uid does not need checking or top-

ping up. The only maintenance operation required

is charging, for example after extended storage.

The battery can be charged:

- by the engine;

- by a battery charger.

9.8.1 Charging by the engine

This method is only an option if there is still

enough charge in the battery to be able to start the

engine.

• If the battery is new, connect the relative leads.

• Take the machine outside. Alternatively, con-

nect an exhaust extraction device to the engi-

ne’s exhaust pipe to remove toxic fumes.

• Start the engine by following the instructions

provided in this manual.

• Leave the engine running continuously for 45

minutes (the time needed to fully charge the

battery).

• Turn o the engine.

9.8.2 Charging with a battery charger

Use a constant voltage battery charger.

Use of a standard charger may damage

the battery. For further information, ple-

ase contact your dealer.

Before connecting the battery charger,

disconnect the battery from the electri-

cal system.

9.8.3 Disassembly/assembly

The battery is housed under the engine casing

(30:B).

To get to the battery, proceed as follows:

1. Close the fuel cock (24:B).

2. Open the bonnet (see 6.1).

3. Take the key out of the main power switch

(see 6.2).

4. Remove the engine casing (see 7.5.1).

5. Remove the battery holder (31:B) by undoing

the two screws (31:C).

6. Disconnect the black cable (=negative).

7. Partially extract the battery (31:A) from its

seat.

8. Disconnect the red cable (=positive).

9. Replace the dead battery.

10. Connect the red cable to the battery’s posi-

tive terminal (+).

11. Push the new battery into its seat.

Warning: when pushing the battery in,

accompany the red cable to make sure

it doesn’t get trapped: this would pre-

vent correct positioning of the battery

in its seat.

12. Connect the black cable to the battery’s ne-

gative terminal (-).

13. Reposition the battery holder.

14. Replace the engine caring (see 7.5.2).

15. Insert the key in the main power switch (only

if you intend to use the machine).

16. Close the bonnet.

17. Open the fuel cock (only if you intend to use

the machine).

If the leads are disconnected/con-

nected in the wrong order, there is a

risk of a short-circuit and damage to the

battery.

If the leads are interchanged, the alter-

nator and the battery may be damaged.

Tighten the leads securely. Loose leads



Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga Pro 740 IOX - P 901 PH in the language / languages: All languages as an attachment in your email.

The manual is 160,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiga Pro 740 IOX - P 901 PH Manual

Product: