608479
85
Zoom out
Zoom in
Previous page
1/118
Next page
9
4.4 LEVIER DU FREIN DE STATIONNE-
MENT (Fig. 4.1 nº 4)
Ce levier sert à emcher à la machine de se 
déplacer lorsqu’elle est à l’arrêt. Le levier d’em-
brayage a deux positions, correspondant à:
«A»  =   Frein retiré 
«B»   =  Frein inséré
–  Pour enclencher le frein de stationnement, 
appuyer à fond sur la pédale  (4.21 ou 4.31) 
et porter le levier en position «B»; quand on 
relâche le pied de la pédale, le frein reste blo-
qué en position abaissée.
–  Pour déclencher le frein de stationnement, 
appuyer sur la pédale (4.21 ou 4.31), ainsi le 
levier se reporte en position «A».
4.5 COMMANDE D’EMBRAYAGE ET FREIN
DES ORGANES DE COUPE (Fig. 4.1
nº 5)
L’interrupteur coup de poing permet d’insérer les 
organes de coupe grâce à un embrayage élec-
tromagnétique:
«A»  Appuyé = organes de coupe dé-
brayés. 
«B»  Tiré = organes de coupe embrayés. 
–  Si les organes de coupe sont embrayés sans 
que les conditions de sécurité prévues ne 
soient respectées, le moteur s’éteint ou ne 
peut pas être démarré (voir 5.2).
–  Débrayer les organes de coupe (position 
«A»), un frein est actionné en même temps et 
bloque leur rotation en quelques secondes.
4.6 LEVIER DE RÉGLAGE DE LA
HAUTEUR DE TONTE (Fig. 4.1 nº 6)
Ce levier se règle sur sept positions marquées 
de «1» à «7» sur l’étiquette correspondante et 
indiquant autant de hauteurs de tonte comprises 
entre 3 et 8 cm.
Pour passer dune position à l’autre, il faut
déplacer latéralement le levier et le placer de 
nouveau dans l’un des crans d’arrêt.
4.7 VOYANT ET DISPOSITIF DE SIGNALI-
SATION ACOUSTIQUE (Fig. 4.1 nº 7)
–  L’avertisseur sonore avertit que le bac de ra-
massage est plein (voir 5.4.6).
–  Le voyant s’allume quand la clé (4.3) se trouve 
en position «MARCHE», et reste toujours al-
lumé pendant le fonctionnement.
–  Quand il clignote, cela signie qu’il manque 
une autorisation au démarrage du moteur  
(voir 5.2).
4.8 LEVIER DE RENVERSEMENT DU BAC
DE RAMASSAGE (si prévu)
(Fig. 4.1 nº 8)
Ce levier, extractible de son siège, permet de 
renverser le bac de ramassage pour le vider, en 
réduisant leort que doit fournir lopérateur.
4.9 BOUTON D’AUTORISATION DE TONTE
EN MARCHE ARRIÈRE (Fig. 4.1 nº 9)
En maintenant le bouton appuyé, il est possible 
de reculer avec les organes de coupe em-
brayés, sans provoquer l’arrêt du moteur. 
Transmission mécanique
4.21 PEDALE EMBRAYAGE / FREIN
(Fig. 4.2 nº 21)
Cette pédale exerce une double fonction:
sur la première partie de sa course, elle ac-
tionne l’embrayage en activant ou en ar-
tant la rotation des roues; sur la deuxième, 
elle agit en tant que frein sur les roues arri-
ères.
IMPORTANT Il faut faire très attention à
ne pas maintenir la pédale dans une position
intermédiaire lors de l’embrayage ou du dé-
brayage: la courroie de transmission du mou-
vement peut surchauffer et s’abîmer.
REMARQUE Ne pas tenir le pied appuyé
sur la pédale pendant la marche.
4.22 LEVIER DE CHANGEMENT DE
VITESSE (Fig. 4.2 nº 22)
Ce levier se règle sur sept positions cor-
respondant aux cinq vitesses de marche 
avant, au point mort «N» et à la marche ar-
rière «R». 
Pour passer d’une vitesse à lautre, appuyer 
sur la première partie de la course de la -
dale (4.21) et déplacer le levier selon les in-
dications reportées sur l’étiquette.
ATTENTION! La marche arrière doit
être insérée à l’arrêt.
85


Need help? Post your question in this forum.

Forumrules
1

Forum

stiga-estate-3084-h

Reset search

  • the mower wont go into mowing drive when I lift the button
    Submitted on 7-3-2023 at 06:09

    Reply Report abuse
  • The engine cuts out if the forward pedal is pushed down.. it is not the seat cut out or the grass catcter off Submitted on 23-12-2022 at 01:10

    Reply Report abuse
  • I need information on replacing the Deck cutting belt Submitted on 28-5-2020 at 15:47

    Reply Report abuse
  • my stiga 3084H , with the wheels straight , the steering wheel is no longer aligned .The steering rods don't appear to be bent. Could the steering cog have jumped a tooth on the rack?
    Dave Submitted on 8-12-2018 at 20:29

    Reply Report abuse
  • HELP My stiga estate 3084h mower starts without having to press the foot brake and occasionally stops after a few seconds then it will not start leave it for a couple of minutes and it will start I have changed all the safety micro switches but it is still the same any suggestions please
    Thank you in advance Submitted on 2-7-2018 at 08:44

    Reply Report abuse
  • How do I level the cutting deck, it is 20mm higher on one side Submitted on 4-9-2017 at 16:25

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga ESTATE 3084 H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga ESTATE 3084 H in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stiga ESTATE 3084 H

Stiga ESTATE 3084 H User Manual - Danish, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish - 192 pages

Stiga ESTATE 3084 H Additional guide - All languages - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info