Manual Stiga ESTATE 3084 H (page 74 of 118) (English, German, Dutch, French, Italian)

608479

74

Zoom out

Zoom in

Previous page

1/118

Next page

16

7. TROUBLESHOOTING

PROBLEM LIKELY CAUSE SOLUTION

1. With the key on «ON», the light

stays o

The safety device of the electronic

circuit board has cut in due to:

– badly connected battery

– battery terminals crossed

– at battery

– blown fuse

– wet circuit board

Turn the ignition key to «STOP»

and look for the cause of the

problem:

– check connections (see 3.4)

– check connections (see 3.4)

– recharge the battery (see 6.2.3)

– replace the fuse (10 A)

(see 6.3.5)

– dry using luke warm air

2. With the ignition key turned to

«START» the light ashes and

the starter motor does not run

– starting conditions have not

been met

– check that all starting conditions

are met (see 5.2.a)

The wheels are held by a snap ring (1) which

can be removed with a screwdriver.

NOTE If you have to replace one or both rear

wheels, make sure that any differences in their

external diameter does not exceed 8-10 mm; on

the contrary, you must adjust the cutting-means

assembly alignment to prevent uneven mowing.

IMPORTANT Before remounting the wheel,

apply grease to the axle. Put the snap ring (1)

and shoulder washer (2) back in place.

6.3.3 Repairing or replacing tyres

The tyres are “Tubeless” and must be replaced

or repaired if punctured by a specialized tyre

repairer following the procedures required for

this kind of tyre.

6.3.4 Replacing bulbs ( if tted)

• Type “I” bulbs (incandescent) (Fig. 6.5)

The bulbs (18W) have a bayonet tting and are

installed in the bulb holder which can be taken

out by turning it anti-clockwise with pliers.

• Type “II” bulbs (LED) Fig. 6.6)

Unscrew the ring-nut (1) and remove the con-

nector (2).

Remove the LED illuminator (3), secured by

screws (4).

6.3.5 Replacing a fuse (Fig. 6.7)

The machine is tted with fuses (1) with dierent

capacities and functions. Specically:

– 10 A fuse = protects the main and power cir-

cuits of the electronic circuit board. When it

blows, the machine stops and the dashboard

light switches o.

– 25 A fuse = protects the battery recharge cir-

cuit. When it blows, the battery gradually runs

down and the machine will have problems

starting.

The fuse capacity is indicated on the fuse.

IMPORTANT A blown fuse must always be

replaced by one of the same type and ampere

rating, and never with one of another rating.

If you are unable to understand why it has

blown, contact Your Dealer.

6.3.6 R emoving, replacing and

reassembling of cutting means

WARNING! Always wear strong protec-

tive gloves to handle the cutting means.

WARNING! Always replace damaged or

bent cutting means; never attempt to repair

them! ALWAYS USE ORIGINAL CUTTING

MEANS!

Only cutting means bearing the code indicated

in the table on page ii must be used on this ma-

chine.

Given product evolution, the above mentioned

cutting means may be replaced in time with oth-

ers having similar interchangeable and operat-

ing safety features.

IMPORTANT Cutting means should be

replaced in pairs, especially when there are

marked differences in wear.

1

the mower wont go into mowing drive when I lift the button
Submitted on 7-3-2023 at 06:09
Reply Report abuse
The engine cuts out if the forward pedal is pushed down.. it is not the seat cut out or the grass catcter off Submitted on 23-12-2022 at 01:10
Reply Report abuse
I need information on replacing the Deck cutting belt Submitted on 28-5-2020 at 15:47
Reply Report abuse
my stiga 3084H , with the wheels straight , the steering wheel is no longer aligned .The steering rods don't appear to be bent. Could the steering cog have jumped a tooth on the rack?
Dave Submitted on 8-12-2018 at 20:29
Reply Report abuse
HELP My stiga estate 3084h mower starts without having to press the foot brake and occasionally stops after a few seconds then it will not start leave it for a couple of minutes and it will start I have changed all the safety micro switches but it is still the same any suggestions please
Thank you in advance Submitted on 2-7-2018 at 08:44
Reply Report abuse
How do I level the cutting deck, it is 20mm higher on one side Submitted on 4-9-2017 at 16:25
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Stiga ESTATE 3084 H at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga ESTATE 3084 H in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stiga ESTATE 3084 H

Stiga ESTATE 3084 H User Manual - Danish, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish - 192 pages

Stiga ESTATE 3084 H Additional guide - All languages - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info