608718

Stiga B 33 Manual

111
Zoom out
Zoom in
Previous page
1/408
Next page
USE OF THE ENGINE (Fig. 8)
Cutting device speed is regulated by the throttle 
trigger (2), located on the rear handgrip (4) or the 
right handgrip (4a) of the handlebar.
The throttle trigger only works if the lockout (3) is 
pressed at the same time.
The movement is transmitted from the engine to 
the drive shaft  by  a  centrifugal mass clutch that 
prevents the shaft from moving when the engine 
is running at minimum speed.
WARNING!
Do not use the machine if
the cutting device moves when the engine is
running idle; in this case, contact you dealer.
The  correct  running  speed  will  be  achieved  by 
pressing the throttle trigger (2) as far as possible.
IMPORTANT
Avoid using the engine at full
power for the rst 68 working hours.
STOPPING THE ENGINE (Fig. 8)
To stop the engine:
–   Release the throttle trigger (2)  and  allow  the 
engine to run idle for a few seconds.
–   Set the switch (1) to «STOP».
WARNING!
When you have reduced
speed to a minimum, it will take a few seconds
for the cutting device to stop
3.   Press the primer device button (6) 3 or 4 ti mes 
to prime the carburettor.
4.   Hold the machine rmly on the ground with one 
hand on the power  unit,  in  order  not  to  lose 
control of the machine during startup (Fig. 9).
IMPORTANT
To prevent distortions, the
drive tube must not be used as a support for the
hand or knee during startup.
5.   Pull the starter rope slowly for 10 - 15 cm until 
you feel some resistance, then tug it hard a few 
times until you hear the engine turn over.
IMPORTANT
To avoid breaking the sta r ter
rope, do not pull the whole length of it or let it slide
along the edge of the cable guide hole. Release
the starter gradually, to avoid letting it y back un-
controllably.
6.   Pull the starter rope again until the engine starts 
as normal.
WARNING!
Starting the engine with
the choke engaged causes the cutting device
to move, only stopping when the choke is di-
sconnected.
7.    When  the  engine  is  started,  disconnect  the 
starter by turning the lever (2) to  «RUN».
8.   Briey  activate  the  throttle  (2)  to  bring  the 
engine down to minimum,  with the  switch (1) 
which will  move  automatically  to  the  «RUN» 
position.
9.   Let the engine run idle for at  least  1  minute 
before using the machine.
IMPORTANT
If the starter rope is pulled
repeatedly with the choke on, it may ood the en-
gine and make starting dicult.
If you have ooded the engine, remove the spark 
plug and gently pull the handle on the starter rope 
to eliminate any excess  fuel;  then  dry  the spark 
plug electrodes and replace it on the en gine.
•  Hot starting
When hot starting (immediately after stopping the 
engine):
–  Set the switch (1) to position «RUN», then follow 
points 4 - 5 - 6 – 9 in the previous procedure.
 HOW TO START - USE - STOP THE ENGINE 109
EN
… 111 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga B 33 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga B 33 in the language / languages: All languages as an attachment in your email.

The manual is 7,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info