608716

Stiga B 28 D Manual

108
Zoom out
Zoom in
Previous page
1/408
Next page
•  3 or 4 point blade  (Fig. 4)
WARNING!
Wear protective gloves
and t the blade guard.
–   Remove  the  blade  (if  tted)  as  described  in 
paragraph 4.
–   The guard (1) is xed to the angle transmission 
(2) by four screws (3).
• Cutting line head  (Fig. 5)
WARNING!
When using the cutting
line head the additional guard, with line cut-
ting knife, must always be tted.
–   Remove  the  blade  (if  tted)  as  described  in 
paragraph 4.
–   The guard (1) is xed to the angle transmission 
(2) by four screws (3).
–   Assemble the  additional guard (4)  fastening it 
into place on the guard (1).
4.   REMOVING AND REFITTING
THE CUTTING DEVICES
WARNING!
Use only original cutting
devices or ones homologated by the Ma nu-
facturer.
•  3 or 4 point blade (Fig. 6)
WARNING!
Wear protective gloves
and t the blade guard.
NOTE
The fastening nut (5) has a
left-hand thread and so must be unscrewed in a
clockwise direction and screwed up anticlockwise.
–   Insert the wrench supplied (2) into the specic 
hole in the angle transmission (3) and rotate the 
blade (1) by hand until the wrench  enters  the 
inner hole, blocking rotation.
–   Remove the split pin (4) and unscrew the nut (5) 
in a clockwise direction.
–   Pull out the washer (6) and the outer ring-nut (7) 
and remove the blade (1).
IMPORTANT
The machine is supplied with
some of the components disassembled and the
fuel tank empty.
WARNING!
Always wear strong work
gloves to handle the cutting devices. Mount
the components very carefully so as not to
impair the safety and eciency of the ma
chine. If in doubt, contact your dealer.
1.  COMPLETING THE MACHINE
1a. “MONO” models (Fig. 1)
–   Position the upper part (2) with the front grip’s 
guard on the drive tube (1).
–   Fasten the lower cap (4) inserting the pin (4a) in 
one of the three holes on the drive tube.
–  Fully tighten the screws (4).
1b. “DUPLEX” models (Fig. 2)
–   Loosen the screws (5) and remove the cap (4) 
from the support (2).
–   Put the handlebar (1) into the seating in the sup-
port (2), located on the drive tube (3), making 
sure that the controls are on the right.
–   Fit the cap (4), fully tightening the screws (5).
–   Fasten the casing (6) of the controls to its cable 
fastener (7). 
2.  MOUNTING THE ROD
(Models with separate rod – Fig. 3)
–   Pull out the stop pin (5) and push the lower part 
of the  rod (4) right  down until the stop pin  (5) 
slots into the hole (6) in the rod. This is easier to 
do if you rotate the bottom of the rod (4) slightly 
in both directions. The pin (5) is in place when it 
is completely lodged in the hole.
–  Lastly, tighten the knob (7) securely.
3.  FITTING THE GUARDS
WARNING!
Each cutting device is pro-
vided with a specic guard. Never use guards
other than those indicated for each cutting
device.
106 MACHINE ASSEMBLY
EN
  4.  MACHINE ASSEMBLY
… 108 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga B 28 D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga B 28 D in the language / languages: All languages as an attachment in your email.

The manual is 7,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info