564045
33
Zoom out
Zoom in
Previous page
1/578
Next page
31
User’s manual
EN
Problem Cause Remedies
“Too high grass” or
“Blade Error”appears on the display
Cutting blade damaged Replace the blade with a new one (see “Blade Replacement”)
Cutting blade clogged by residuals (tape, cords,
plastic fragments, etc.)
Stop the robot safely (see “Robot Safety Stop”)
Warning – Caution
Use protective gloves to prevent injuries to your hands
Unclog the blade
The robot was started too close to obstacles (less
than a distance of 1 m) or in the presence of
obstacles (fallen branches, forgotten objects, etc.)
Stop the robot safely (see “Robot Safety Stop”)
Remove the obstacles and restart the robot (see “Start-up and
manual stopping of the robot (in closed areas)”)
Electric motor failure
Have the motor replaced or repaired by your nearest
authorised service centre
Grass too high
Increase the cutting height (see “Adjustment of Cutting
Height”). Perform a preliminary cutting of the area with a
normal lawnmower
The remote control does not work Programming error
Correctly program the remote control (see “Programming
Mode”)
“WatchdogError” appears on the
display
The internal “software safety” system is enabled
Turn the robot off and on.
If the problem persists, contact your nearest authorised service
centre
“Tilt” appears on the display
The robot is located on a level that is higher than
the allowed limits
Mark off the area that is too steep
The robot is located on a level that is lower than
the allowed limits
Check that the charging station is positioned on a at surface.
Turn the robot off and on while in the charging station and try
again. If the problem persists, contact your nearest authorised
service centre
(C)
The led
( c ) does
not turn on
No power supply
Make sure the power supply unit is correctly connected to the
power outlet
Interrupted fuse
Have the fuse replaced by your nearest authorised service
centre
The
transmitter
LED (C) is on
Interrupted perimeter wire
Stop the robot safely (see “Robot Safety Stop”). Disconnect
the power plug from the power supply unit. Join the perimeter
wire
PART REPLACEMENT
RECOMMENDATIONS FOR REPLACING PARTS
Important
Replace and repair any parts according to the manufacturer’s instructions, or contact the service centre if these operations
are not included in the manual.
BATTERY REPLACEMENT
Important
Replace the batteries at an authorised service centre.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga Autoclip 527 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga Autoclip 527 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 115,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info