516571

Stiga Autoclip 325 Manual

14
Zoom out
Zoom in
Previous page
1/578
Next page
12
User’s manual
EN
Marking the boundary of the work area
3. Check the entire lawn surface and assess whether it is necessary
to divide it into separate work areas as per the rules described here
below. Before installing the perimeter wire, check the entire path to
make this procedure easier. The illustration shows a lawn with the
track for installation of the perimeter wire.
During installation, identify any secondary areas and closed areas. A
secondary area is part of a lawn connected to the primary lawn with
a passage that is diffi cult to reach by the robot's normal movement.
The area must be reachable without any rises or drops greater than
those allowed. Whether a zone is to be defi ned a “secondary area”
also depends on the size of the primary area. The larger the primary
area, the harder it will be to reach narrow passages. More generally,
a passage narrower than 200 cm (78.74 ") is considered a secondary
area. The number of secondary areas managed depends on the
characteristics of the model (See “Technical Specifi cations”).
The minimum passage allowed is 70 cm (27.56 ") from each edge of
the perimeter wire. The perimeter wire must be positioned at a distance
of (to be indicated below) from any objects outside the lawn; therefore,
the total passage available should be 140 cm (55.12 ").
If this passage is very long, the width should not be greater than 70 cm
(27.56 ").
During programming, it is necessary to confi gure the size of the
secondary areas as a percentage of the lawn, and the quickest
direction for reaching it (clockwise or counter-clockwise), as well as
the number of meters of wire needed to reach the secondary area. See
“Programming Mode.”
24 v
Track for laying the perimeter wire
min. 70 cm / 27,56 "min. 70 cm / 27,56 "
min. 70 cm / 27,56 "
If the aforesaid minimum requirements are not met i.e. an area
separated by a rise or drop with characteristics that cannot be
managed by the robot or a passage (corridor) narrower than 70 cm
(27.56 ") from perimeter edge to perimeter edge, then this area of the
lawn is considered a “Closed Area.” To mark a “Closed Area” lay the
outgoing and incoming perimeter wire in the same track at a maximum
distance of 1 cm (0.40 "). In this case, the robot is unable to reach the
area autonomously, and must be managed as described in the chapter
“Management of Closed Areas.” The management of “Closed Areas”
reduces the square meters that can be managed autonomously by
the robot.
corridor with a minimum passage
of 70 cm / 27,56 " from edge to edge.
PRIMARY AREA
SECONDARY AREA
corridor with a passage
< 70 cm / 27,56 "
PRIMARY AREA
CLOSED AREA
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga Autoclip 325 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga Autoclip 325 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 112,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info