608620

Stiga 107M HD Manual

8
Zoom out
Zoom in
Previous page
1/11
Next page
ENGLISH
EN
5. Undo the screws (7:H and 12:K) so that the
deck rests against the plank and the spacer.
Check that the deck does not lean sideways in
relation to the machine.
6. Tighten the screws (7:H and 12:K) to 22 Nm.
7. Place the deck in transport position and remove
the plank.
4 USING THE MACHINE
Check that the grass that is to be cut is
completely free of foreign objects such
as stones etc.
4.1 Cutting height
The best cutting results are achieved when the
when the top third of the grass is cut off. I.e. 2/3 of
the length of the grass remains. See fig. 18.
If the grass is long and has to be cut significantly,
cut twice using different cutting heights.
Do not use the lowest cutting heights if the lawn
surface is uneven. This would entail a risk of the
blades being damaged against the surface and the
lawn’s top layer of soil being removed.
4.2 Incline
The cutting deck’s rear section can be lifted so that
the deck has a greater forward incline than that
provided by the basic setting. This incline affects
the cutting results as follows.
4.2.1 No incline
When the deck is in the basic setting, the best
mulching effect and good dispersion of the cut
grass are achieved. The basic setting is recom-
mended for normal grass.
4.2.2 Incline
When the cutting deck is inclined forwards, the
mulching effect is reduced while the cut grass is
dispersed better.
Inclining forwards is recommended for thicker
grass.
4.3 Mowing advice
In order to achieve optimum mowing results, fol-
low the advice below:
• Cut frequently.
• Run the engine at full throttle.
• The grass should be dry.
• Use sharp blades.
• Keep the underside of the cutting deck clean.
4.4 125 Combi Pro
125 Combi Pro can cut the grass in the following
two ways:
• Mulching: composting and spreading.
• Rear ejection: ejects the grass in a line behind
the deck.
The deck is set for mulching on delivery. In order
to eject the grass in a line behind the deck, the plug
in fig. 6 must be removed.
Set the deck in service position (see 5.3) in order to
remove/install the plug.
5 MAINTENANCE
5.1 Preparation
All service and all maintenance must be carried out
on a stationary machine with the engine switched
off.
Prevent the machine from rolling by al-
ways applying the parking brake.
Stop the engine.
Prevent unintentional starting of the
engine by disconnecting the spark plug
cable from the spark plug and remov-
ing the ignition key.
5.2 Washing position
1. Activate the parking brake.
2. Set the implement lifter in transport position.
3. Set the lowest cutting height.
4. 125 Combi Pro, 107 M HD, 121 M:
Disconnect the rear section of the cutting deck
by removing pins and any washers. See fig. 2,
7:I and 13.
107 M:
Lift up the rear section of the cutting
deck, undo the catches (12:L) and lower.
5. Grip the front edge of the deck and lift up. Hook
on the chain so that the deck is pointing diago-
nally upwards. See fig. 19.
It is absolutely forbidden to start the engine
when the deck is in the washing position.
Reset 125 Combi Pro in accordance with 3.1.1,
point 8.
Reset 107 M HD in accordance with 3.2.1, point 7.
Reset 121 M in accordance with 3.2.1, point 7.
Reset 107 M in accordance with 3.3.1, point 7.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiga 107M HD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiga 107M HD in the language / languages: English as an attachment in your email.

The manual is 0,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info