650328
7
Zoom out
Zoom in
Previous page
1/20
Next page
ENGLISH
 


Pipe set, offset installation
This pipe set with pipe bends is required if you want to have the
appliance vertically offset against the water connection by approx.
90 mm downwards.
Pipe set for replacing a gas water heater
This pipe set is required if the installation has existing gas water
heater connections (cold water connection on the left and DHW
connection on the right).
DHB replacement pipe set
2 water couplings. These allow the appliance to be connected to
the available water plug-in connections of a DHB.
Load shedding relay LR 1-A
The load shedding relay for installation in the electric distribution
board enables priority control of the instantaneous water heater
when electric storage heaters are being operated simultaneously,
for example.
ZTA 3/4 – Central thermostatic valve
Thermostatic valve for centralised premixing, e.g. an instantaneous
water heater in conjunction with a solar thermal system.
9. Installation
9.1 Installation information
9.1.1 Flow pressure
If the ow rate required for the appliance to switch on is not
achieved even with the tap fully open, remove the flow limiter.
Replace it with the plastic profile washer supplied. If required the
pressure in the water installation can also be raised.
Note
For the thermostatic valve to function correctly, the flow
limiter for this valve must not be replaced with the plastic
profile washer.
2
1
2602�02�0820
1 Flow limiter
2 Plastic profile washer
9.1.2 Flexible water connection lines
If the appliance is connected with exible water connection lines,
ensure that the bayonet fittings of the pipe bends do not become
twisted inside the appliance.
9.1.3 Appliance with changeover connected load
The appliance DHB-E 18/21/24 SLi is set to 21kW when delivered.
If the appliance is installed with a different output, take the
following steps:
Re-plug the coding card according to the selected output; for
selectable output and fuse protection of the appliance see
"Specification“.
Mark the selected output on the type plate using a
permanent marker.
Install the flow limiter with a rating corresponding to that of
the appliance. The colour of the flow limiter is given in the
table "Specification".
2602�02�0822
10. Installation
10.1 Installation location
The appliance is exclusively designed for installation on a solid
wall. Ensure that the wall has a sufficient load-bearing capacity.
Always install the appliance vertically (over or undersink) in a
room free from the risk of frost.
10.1.1 Undersink
1
2
2602�02�0807
1 Cold water inlet
2 DHW outlet
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stiebel Eltron DHB-E 18 SLi 25A electronic at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stiebel Eltron DHB-E 18 SLi 25A electronic in the language / languages: English as an attachment in your email.

The manual is 7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stiebel Eltron DHB-E 18 SLi 25A electronic

Stiebel Eltron DHB-E 18 SLi 25A electronic Usermanual and installation guide - English, German, Dutch, French, Polish - 116 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info