593302
8
Zoom out
Zoom in
Previous page
1/12
Next page
Troubleshooting *
SensorLight without power
SensorLight will not switch ON
SensorLight will not switch OFF
SensorLight switches ON without any
identifiable movement
SensorLight does not switch ON
despite movement
Malfunction
House fuse faulty, not switched ON,
break in wiring
Short circuit in mains power supply
lead
Any mains switch OFF
Renew house fuse, switch ON
mains power switch, check wiring
with voltage tester
Check connections
Switch ON mains power switch
Wrong twilight setting selected
Bulb faulty
Mains switch OFF
House fuse faulty
Adjust setting
Replace bulb
Switch ON
Renew house fuse,
check connection if necessary
Continuous movement in the
detection zone
Check zone
Light not mounted for detecting
movement reliably
Movement occurred, but not identi-
fied by the sensor (movement behind
wall, movement of a small object in
immediate lamp vicinity etc.)
Securely mount enclosure
Check zone
Rapid movements are being sup-
pressed to minimise malfunctioning
or the detection zone you have set
is too small
Check zone
Cause Remedy
Functional Warranty
This STEINEL product has been manufactured with
great care, tested for proper operation and safety in
accordance with applicable regulations and then sub-
jected to random sample inspection. STEINEL guar-
antees that it is in perfect condition and proper work-
ing order. The warranty period is 36 months, starting
on the date of sale to the consumer. We undertake to
remedy faults caused by material or manufacturing
defects. This warranty undertaking shall be performed
by the repair or replacement of the defective parts, at
our own discretion. The warranty does not cover
damage to wear parts, nor does it cover damage or
defects caused by improper treatment, maintenance
or the use on non-genuine parts. Further consequen-
tial damage to external items is excluded.
Claims under warranty will only be accepted if the
product is sent fully assembled and well packed
complete with receipt or invoice (date of purchase
and dealer's stamp) to the appropriate service centre.
Repair Service:
Please ask your nearest service
centre how to proceed for repairing
faults not covered by the warranty or
occurring after the warranty expires.
* only applies to RS PRO 500/1000/2000 IP65 Sensor
Declaration of conformity
This product complies with
- Low Voltage Directive 2006/95/EC
- EMC Directive 2004/108/EC
- RoHS Directive 2011/65/EC
- R&TTE Directive 1999/05/EC
- WEEE Directive 2012/19/EC
The following items are available as accessories:
1. LED orientation light:
Push-fit module with orientation light. Allows
illumination with “residual light”. Only when you
enter the reach detection of the light will the latter
be 100% illuminated.
Permanent supply of the slave lights with supply
voltage is required.
2. LED orientation light with storage battery:
As 1., but also operational in case of a power cut,
since the LED's are supplied by the storage battery.
3. Wireless module:
Plug-in module only for RS Pro 1000/2000 IP65
Sensor and Slave. The slave light or another master
light is remotely switched by radio signal (useful for
example in old buildings or for retrofitting as no addi-
tional wiring is necessary).
Modules as accessories
Twilight setting (response threshold)
Factory setting: daylight operation (2000 lux)
The sensor's response
threshold can be infinitely
varied from 2 – 2000 lux.
Control dial set to = daylight
operation approx. 2000 lux.
Control dial set to = night-time
operation approx. 2 lux (10 lux RS PRO 500 IP65).
Teach mode:
At the light level at which you want the SensorLight
to respond to movement, the control should be set
to . After 10 sec. the value of the ambient bright-
ness is saved. Before this time elapses, the glass
shade must be applied. There must be no LED
module switched on.
Time setting (switch-off delay)
Factory setting: shortest time (1 minute)
Light ON duration can be infinitely
varied from 1 min. to 20 min.
Control dial set to =
shortest time (1 min.)
Control dial set to + =
longest time (20 min.)
Note: After the light switches OFF, it takes approx.
1 sec. before it is able to start detecting movement
again. The light will only switch on in response to
movement once this period has elapsed.
Install mode:
If the setting below 1 is selected, the device will
switch to "install mode". The light switches on for
3 sec. as soon as motion is detected. Unnecessary
waiting time can therefore be avoided during adjust-
ment. Since the lamp is subject to heavy wear in this
mode, the fixture quits the mode automatically after
10 min. The minimum time (1 min.) applies in this case.
The glass shade should also be applied in this mode.
Important: Teach mode and Install mode cannot be
used at the same time. The wireless module must not
be plugged in when using the Install mode.
Reach setting (sensitivity)
Factory setting: maximum reach (8 m)
Reach is the term used to describe
the diameter of the more or less
circular detection zone produced
on the ground after mounting the
sensor light at a height of 2.5 m.
Control dial set to = minimum reach (1 m)
Control dial set to + = maximum reach (8 m)
By inserting the shrouds supplied, the reaches can
be reduced in four directions (see drawing ).
Note: During adjustment, use the "install mode"
(see time setting).
If a mains switch is installed in the mains supply lead,
the light is capable of the following functions in addition
to the simple ON/OFF function:
Sensor operation
1) Switch light ON (when light is OFF):
Turn switch OFF and ON once.
Light stays ON for the period selected.
2) Switch light OFF (when light is ON):
Turn switch OFF and ON once.
The light goes out or switches over to sensor mode.
Manual override
1) Activate manual override:
Turn switch OFF and ON twice. The light is set to
manual override for 4 hours.
2) Deactivate manual override:
Switch OFF and ON once. The light goes out or
switches over to sensor mode.
Important:
The switch should be actuated in rapid succession
(in the 0.5 – 1 sec. range).
Manual override
1 – 20 min.
* only applies to RS PRO 500/1000/2000 IP65 Sensor
2 – 2000 lux
1 m–8 m dia.
Recommendation:
Fluorescent tube manufacturers recommend season-
ing, or burning in, new tubes for 100 hours so as not
to restrict tube service life. To follow this recommen-
dation and to ensure trouble-free sensor operation
particularly at low ambient temperatures, new fluores-
cent tubes should undergo the following seasoning
procedure.
1. Connect light and switch ON.
2. Turn all 3 setting controls fully clockwise, then turn
the middle setting control fully anticlockwise and
fully clockwise again (within 10 sec.).
3. The seasoning process is confirmed by switching
the light OFF twice and then back ON again.
4. Now turn all controls to the chosen settings.
5. The light is now left ON for 100 hours without sen-
sor function. Do not disconnect the light from the
mains power supply during this period.
6. The luminaire automatically returns to sensor
mode after 100 hours.
Note:
When fluorescent tubes are new or at low ambient
temperatures, the sensor may not switch the light
OFF as it might be detecting gas moving inside
the tubes. In this case, switch the light OFF and,
for the time being, drastically reduce the reach set-
ting. Please only use high-quality branded lamps.
Otherwise, we cannot guarantee that the high-
precision sensor will operate reliably.
- 15 -- 14 -
GB
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel RS PRO 500 IP65 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel RS PRO 500 IP65 in the language / languages: All languages as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info