Manual Steinel RS LED D1 (page 4 of 10) (English, German, Polish, Spanish)

592499

Zoom out

Zoom in

1/10

Installation instructions

Dear Customer,

Congratulations on purchasing your new STEINEL

SensorLight and thank you for the confidence you

have shown in us. You have chosen a high-quality

product that has been manufactured, tested and

packed with the greatest care.

Please familiarise yourself with these instructions

before attempting to install the SensorLight because

prolonged reliable and trouble-free operation will only

be ensured if it is fitted properly.

We hope your new designer sensor-switched indoor

light will give you lasting pleasure and satisfaction.

System components

햲 Enclosure

햳 HF-sensor

햴 Spacer for surface wiring

햵 Reach setting (3 – 8 m all round)

햶 Time setting (5 sec. – 15 min.)

햷 Twilight setting (2 – 2000 lux)

햸 Light diffuser

Mains connection, surface wiring

Mains connection, concealed wiring

Principle

The SensorLight is an active motion detector. The

integrated HF-sensor emits high-frequency electro-

magnetic waves (5.8 GHz) and receives their echo.

The sensor detects the change in echo from even

the slightest movement in the light's detection zone.

A microprocessor then triggers the "switch light ON"

command. Detection is possible through doors,

panes of glass or thin walls.

Detection zones for ceiling mounting:

1) Minimum reach (3 m dia.)

2) Maximum reach (8 m dia.)

Important: Persons or objects moving towards the

light are detected best.

Detection zones for wall mounting:

3) Minimum reach (3 m dia.)

4) Maximum reach (8 m dia.)

Safety warnings

■ Disconnect the power supply before attempting any

work on the unit.

■ The electrical connection lead must be dead during

installation. Therefore, switch

OFF

the power first

and check that the circuit is dead using a voltage

tester.

■ Installing the sensor light involves work on the

mains voltage supply. This work must therefore

be carried out professionally in accordance with

applicable national wiring regulations and electrical

operating conditions.

(

-VDE 0100,

-ÖVE /

ÖNORM E8001-1,



-SEV 1000)

Note:

The high-frequency output of the HF sensor is approx.

1 mW – that's just 1,000th of the transmission power

of a mobile phone or microwave oven.

- 7 -- 6 -

Betriebsstörungen

SensorLeuchte

ohne Spannung

SensorLeuchte

schaltet nicht ein

SensorLeuchte

schaltet nicht aus

SensorLeuchte schaltet

ohne erkennbare Bewegung ein

SensorLeuchte schaltet trotz

Bewegung nicht ein

Störung

왎 Haussicherung defekt, nicht

eingeschaltet, Leitung unterbrochen

왎 Kurzschluss in der Netzzuleitung

왎 Eventuell vorhandener Netzschalter

aus

왎 neue Haussicherung, Netz schalter

einschalten, Lei tung überprüfen mit

Spannungsprüfer

왎 Anschlüsse überprüfen

왎 Netzschalter einschalten

왎 Dämmerungseinstellung falsch

gewählt

왎 Netzschalter AUS

왎 Haussicherung defekt

왎 neu einstellen

왎 einschalten

왎 neue Haussicherung, evtl. Anschluss

überprüfen

왎 dauernde Bewegung im

Erfassungsbereich

왎 Bereich kontrollieren

왎 Leuchte nicht erschütterungsfrei

montiert

왎 Bewegung lag vor, wurde jedoch

vom Beobachter nicht erkannt

(Bewegung hinter Wand, Be-

wegung eines kleinen Objektes in

unmittelbarer Leuchtennähe etc.)

왎 Gehäuse fest montieren

왎 Bereich kontrollieren

왎 schnelle Bewegungen werden zur

Störungsmini mierung unterdrückt

oder Erfassungsbereich zu klein

eingestellt

왎 Bereich kontrollieren

Ursache Abhilfe

approx. 1 mW

approx. 1000 mW

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel RS LED D1 in the language / languages: English, German, Polish, Spanish as an attachment in your email.

The manual is 0,71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel RS LED D1 Manual

Product: