Once the light has been fully assembled, it can be
put into operation. Control dials are provided on the
sensor unit for selecting time, twilight and programme
settings. After pressing the engagement lug with
Functions ,,
- 15 -
a flat-bladed screwdriver, the sensor unit can be
removed for ease of setting. When the sensor is
removed, the light automatically switches to constant
output.
Switch-off delay
(time setting)
(factory setting: 5 sec.)
Light ON time can be adjusted continuously
from 5 sec. to 15 min.
Control dial set to – = shortest time (5 sec.)
Control dial set to + = longest time (15 min.)
When setting the detection zone, it is
recommended to select the shortest time.
Programme setting
(factory setting: programme 1)
What is soft light start ?
The SensorLight comes with a soft light start func-
tion. This means that when the light is switched ON it
does not go directly to maximum output but gradually
increases brightness to 100 % over the space of
one second. Brightness is also gradually reduced
when the light is switched OFF.
* Note on user-friendly economy programme with
filament bulb :
The SensorLight does not have any integrated clock.
The middle of the night is only determined on the
basis of the length of darkness phases. To work per-
fectly, therefore, it is important for the SensorLight
to be permanently connected to the power supply
during this period. During the first night (calibration
phase) basic brightness remains activated throughout
the night. Values remain saved even in the event of
mains power failure.
We recommend not to interrupt the power supply in
programme . As the values are determined over
several nights, the SensorLight should, in the event of
any fault, be observed over several nights to ascertain
whether the switch-off time moves towards midnight.
What is basic brightness ?
Basic brightness provides continuous night-time illu-
mination at approx. 25 % light output. The light only
switches to maximum output of 100 % (for the time
selected, see Switch-off delay ) in response to
movement in the detection zone. The light then
returns to basic brightness (approx. 25 %).
Twilight setting
(response threshold)
(factory setting:
daylight operation 2000 lux)
The sensor's response threshold can be infinitely
varied from 2 – 2000 lux.
Control dial set to = daylight operation
approx. 2000 lux.
Control dial set to = daylight twilight operation
approx. 2 lux.
To adjust the detection zone in daylight, the control
dial must be set to (daylight operation).
5 sec. – 15 min.
2 - 2000 lux
3
3
System components
, , , , Installation options
LED SensorLight enclosure
Glass shade locking screw
Wall mount (light)
MiniSensor cover on the light housing
Sealing plug for wall mount (light)
Sensor unit (removes for ease of setting functions)
Mains power supply lead connection (concealed)
Installation instructions
Safety warnings
■ Disconnect the power supply before attempting
any work on the unit.
■ During installation, the electrical wiring you are
connecting must be dead. Therefore, switch off
the power first and use a voltage tester to check
that the power supply is disconnected.
■ Installing the SensorLight involves work on the
mains voltage supply. This work must therefore
Please familiarise yourself with these instructions
before attempting to install the light because pro-
longed, reliable and trouble-free operation will only be
ensured if it is fitted and used properly.
We hope your new STEINEL designer sensor-
switched outdoor light will bring you lasting pleasure.
be carried out by a qualified electrician in accord-
ance with applicable national wiring regulations
and electrical operating conditions.
(
D
-VDE 0100,
A
-ÖVE/ÖNORM E8001-1,
- SEV 1000)
■ Only use genuine replacement parts.
■ Repairs must only be made by specialist workshops.
Mains power supply lead connection (exposed)
Connecting links
LED light housing
Wall mount (LED light)
Engagement lug for removing the sensor unit
Time setting
Twilight setting
Programme setting
- 14 -
Principle
The integrated high-performance infrared sensor is
equipped with a double 360° sensor that detects the
invisible heat emitted by moving objects (persons,
animals etc.).
The heat detected in this way is converted electroni-
cally into a signal that switches the light ON automat-
ically. Heat is not detected through obstacles, such
as walls or panes of glass. Heat radiation of this type
will, therefore, not trigger the sensor. The unit achieves
a coverage angle of 360° with an aperture angle of
90°. A sneak-by guard ensures coverage below the
sensor.
Important: The most reliable way of detecting motion
is to install the SensorLight with the sensor aimed
across the direction in which a person would walk and
by ensuring that no obstacles (such as trees and walls,
for example) obstruct the line of sensor vision. Reach
is limited when walking directly towards the light.
Installation
The site of installation should be at least 50 cm away
from another light because heat radiated from it may
activate the system. To obtain the specified reach of
8 m, the sensor should be installed at a height of
approx. 1.7 – 2 m.
Connecting the mains supply lead (see illustration)
The mains supply lead is a 3-core cable.
L = phase conductor (usually black or brown)
N = neutral conductor (usually blue)
PE = protective earth conductor (green/yellow)
If you are in any doubt, identify the conductors using
a voltage tester; subsequently disconnect the power
supply again. Connect phase conductor (L), neutral
conductor (N) and protective earth conductor (PE)
to the terminal block.
Note: A mains switch for switching the unit ON and
OFF may of course be installed in the mains supply
lead. A mains switch is required for the manual over-
ride function (see Manual override function) .
Dear Customer,
Congratulations on purchasing your new STEINEL
designer sensor-switched outdoor light and thank you
for the confidence you have shown in us. You have
chosen a high-quality product that has been manu-
factured, tested and packed with the greatest care.
A
B
C
D
E
Standard programme:
●
Soft light start / no basic lighting level
●
LED light panel ON as from
twilight setting (L 675 LED)
User-friendly programme:
●
Soft light start + basic lighting level
●
LED light panel ON as from
twilight setting (L 675 LED)
User-friendly economy programme:
●
Soft light start + basic lighting level
until the middle of the night *
●
LED light panel ON as from twilight setting
to the middle of the night (L 675 LED)
Normal programme:
●
No soft light start / no basic lighting level
●
LED light panel ON only in response to
movement (L 675 LED)
1
2
3
4
GB
GB
