Manual Steinel L 115 S (page 5 of 73) (All languages)

592461

Zoom out

Zoom in

1/73

Installation

Fitting to the wall

Attention: Installation

involves connection to the

mains power supply. 230 V

means danger to life! There-

fore, switch off the power

first and use a voltage test-

er to make sure the wiring

is off circuit. Installing the

SensorLight involves work

on the mains power supply;

this work must therefore be

carried out professionally

in accordance with national

wiring regulations.

Undo the screw on the top.

Remove screw and pull out

wall mount. Do not detach

the internal wiring

connected

to the terminal block but

gently pull out the entire

terminal.

Hold the mounting plate

against the wall and mark

where to the drill the holes,

paying attention to any wir-

ing concealed in the wall.

Drill holes and insert rawl

plugs. To conduct a switch-

ing operation, the mains

connection must be fed

in by at least a two-core

cable.

For this purpose, pierce the

mounting plate and fit seal-

ing plug. After feeding the

cable through, the mount-

ing plate can be screwed

into place and aligned.

Connection of the mains

lead

The mains lead consists of

a 2 to 3-core cable.

L = phase conductor

(usually black or brown)

N = neutral conductor

(usually blue)

PE = protective-earth

conductor, if present

(green/yellow)

If in doubt, the conductors

must be identified with a

voltage tester; subsequently

disconnect the power sup-

ply again. Phase (L) and

neutral conductor (N) must

be connected to the termin-

als already holding a cable

of the same colour. The

protective-earth conductor

(PE) must be sealed off with

insulation tape.

Important: Getting the

cable connections crossed

will produce a short circuit

in the unit or in your fuse

box. In this case, you must

identify the individual con-

ductors once again and

re-connect them. A mains

switch for switching the

light "ON" and "OFF" can

of course be installed in the

mains lead.

Installation instructions

Principle

Movement triggers lights,

alarms and many other

devices. For your con-

venience, for your safety

and your security. Whether

at the front door, on the

garage, patio or carport, in

the stairwell, storage room

or basement, this Sensor-

Light is quickly installed

and ready for operation.

The integrated pyroelectric

infrared detector senses

the invisible heat radi-

ated from moving objects

(people, animals, etc.). This

heat detected in this way

is converted electronically

into a signal that switches

the light on. Heat is not

detected through obstacles,

such as walls or panes of

glass. Heat radiation of this

type will, therefore, not trig-

ger the sensor.

Focal points and angles of

vision of the STEINEL 360°

lens (with 120° angle of

aperture)

a) Sensor lens aimed forward b) Sensor lens aimed down c) Sensor lens aimed back

The most reliable way of

detecting movement is to

install the light with the sen-

sor at a slight angle to the

direction in which a person

would walk and by ensuring

that no obstacles (such as

trees, walls etc.) obstruct

the line of sensor vision.

Please note: Full reach of

12 m is best achieved by

turning only the top row of

lens segments below the

casing.

wall

Detection zone A

12 m

wall

Detection zone B

4 m

wall

Detection zone C

1 m

wall

BLUE

BLACK/

BROWN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel L 115 S in the language / languages: All languages as an attachment in your email.

The manual is 3,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel L 115 S Manual

Product: