Manual Steinel IS 360 D TRIO (page 6 of 51) (All languages)

592545

Zoom out

Zoom in

1/51

- 11 -

Movement triggers lights,

alarms and many other

devices. For your convenience

and safety.

Whether front door, garage,

patio or carport, whether

stairwell, storeroom or base-

ment, this infrared motion

detector is quickly installed

and ready for use at any

chosen site.

The IS 360 D TRIO for ceiling

mounting is equipped with

three 120° pyro sensors that

detect the invisible heat emit-

ted from moving objects

(people, animals etc.). The

heat detected in this way is

electronically converted into a

signal that switches ON loads

(e.g. a light) connected to it.

Heat is not detected through

obstacles, such as walls or

panes of glass, and will

therefore not activate the light.

The three pyro sensors

achieve a coverage angle of

360° with an aperture angle of

180°.

Principle

Detection zone approx. 350 m

Reach max. 12 m

Note: The most reliable way

of detecting movement is to

install the light with the sensor

aimed across the direction in

which a person would walk

and by ensuring that no

obstacles (such as trees,

walls etc.) obstruct the line

of sensor vision.

approx. 5 m 12 m max.

12 m

씮

n Disconnect the power supply

before attempting any work

on the motion detector and

securing it in place.

n During installation, the elec-

trical wiring you are connect-

ing must be dead. Therefore,

switch off the power first and

check cables with a voltage

tester to make sure they are

no longer live.

n Installing the sensor involves

work on the mains power

supply. This means it must

be done properly in accor-

dance with VDE 0100. (

VDE 0100,

-ÖVE-EN 1,



-SEV 1000)

Safety warnings

- 10 -

Ceiling mounting

Caution: Installation means

making connections to the

mains power supply. 230 V

means danger to life!

Therefore, switch off the

power first and use a volt-

age tester to make sure the

wiring is off circuit. Installa-

tion of the sensor involves

work on the mains power

supply; this means it must

be done properly in accor-

dance with VDE 0100.

Please note that the motion

detector must be protected

by a 10 A circuit breaker.

The site of installation

should be at least 50 cm

away from a light source,

because heat radiated from

it may activate the system.

First remove the enclosure

trim

5. To do this, lightly

pinch both depressions

while twisting it anti-clock-

wise and pull it down and

off.

Using a screwdriver, now

undo both fixing screws

1 (anti-clockwise) and

remove the mounting plate.

Do not detach internal

wiring from terminal block,

but gently pull out entire

terminal assembly. Fit the

rubber plug provided into

the mounting plate. Hold

the mounting plate against

the ceiling and mark where

to drill the holes, paying

attention to any wiring

already existing in the ceil-

ing, drill holes; insert wall

plugs. For the motion

detector to trigger a switch-

ing operation, the mains

power must be fed to the

load by at least a two-core

cable. To do this, the rub-

ber plugs can be pierced

with a screwdriver. Two

pre-punched tabs are pro-

vided on the enclosure trim

5 for surface wiring. These

are easy to push through.

The mounting plate can be

screwed to the ceiling after

feeding the cables through.

Finally, return the enclosure

trim 5 and clip into place.

n Connecting the mains

power supply lead

The main supply lead is a

2 to 3-core cable:

L = live conductor

(usually black,

brown or grey)

N = neutral conductor

(usually blue)

PE = any protective

earth conductor

(green/yellow)

If you are in any doubt,

identify the conductors

using a voltage tester; then

disconnect from the power

supply again. The terminal

blocks are for the mains

power supply lead. Connect

the live conductor (L) com-

ing from above to the first

terminal (see arrow) and the

neutral conductor (N) to the

second terminal. Connect

any green/yellow protective

earth conductor to the last

terminal provided.

n Connecting power supply

cable for load

The load cable (e.g. to the

light) is also a 2 to 3-core

cable. Connect this to

terminals N and L’.

Connect the load's live

conductor (black or brown

cable) to the terminal

marked L’. Connect the

neutral conductor (blue

cable) to the terminal

marked N together with the

neutral conductor of the

mains power supply lead.

Connect any green/

yellow protective-earth

conductor to the last

terminal.

Important: Getting the

cable connections crossed

will produce a short circuit

in the light or in your fuse

box. In this case, you must

check the identification of

all cables and re-connect

them. A mains switch for

switching the light ON and

OFF can of course be

installed in the mains lead.

Installing IS 360 D TRIO

Blue Black / brown /

grey

Green / yellow



Installation Instructions

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Steinel IS 360 D TRIO in the language / languages: All languages as an attachment in your email.

The manual is 2,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Steinel IS 360 D TRIO Manual

Product: