592544
10
Zoom out
Zoom in
Previous page
1/66
Next page
1918
After the motion detector has been con-
nected and fastened to its wall mount,
the system can be switched ON.
Two setting options are available after
removing the decorative ring 2.
Switch-off delay (time setting)
(Factory setting: 10 sec.)
Light ON duration can infinitely varied from
approx. 10 sec. to a maximum of 15 min.
Control dial set to (1) =
shortest time (10 sec.)
Control dial set to (6) =
longest time (15 min.)
The shortest time setting is recommended
when adjusting the detection zone and per-
forming the function test.
Function
2 - 2000 lux
approx. 10 sec - max. 15 min
19
Technical specifications
Assuming an installation height of
2 m, the maximum reach of the sensor
is 12 m. Optimum adjustment of the
detection zone is possible according
to needs. The shrouds 6 provided
serve to cover any desired number of
lens segments and individually reduce
the reach. Fine adjustment is also
possible by turning the sensor hous-
ing 3 by ± 80°. The shrouds 6 can be
divided vertically or horizontally along
the grooved divisions, or cut with scis-
sors. After removing the decorative
ring 2, the shrouds are to be sus-
pended on the upper part of the sen-
sor lens. The decorative ring 2 is
subsequently to be reapplied and the
shrouds 6 are fixed firmly in place.
False switching by cars and pedestri-
ans, etc. is therefore ruled out, or risk
areas deliberately monitored.
Reach setting/adjustment
Dimensions (H x W x D): 90 x 60 x 100 mm
Output:
Filament bulbs,
1000 W max., operating on 230 V AC
Fluorescent lamp, 500 W max.,
at cos ϕ = 0.5, inductive load at 230 V AC
6 x 58 W each max., C ≤ 132 µF
operating on 230 V AC
*1)
Connection: 230–240 V, 50 Hz
Angle of coverage: 240° (with 180° angle of aperture)
Pivoting range of
the sensor: Fine adjustment ± 80°
Reach: max. 12 m (electronically stabilised)
Time setting: 10 sec. – 15 min.
Twilight setting: 2 – 2000 lux
IP rating: IP 54
*1)
Fluorescent lamps, low-energy bulbs, LED lights with electronic ballast
(total capacity of all connected ballasts below the value specified).
Twilight setting
(Factory setting: 2000 lux)
The sensor's response threshold can be
infinitely varied from 2 – 2000 lux.
Control dial set to (1) =
daylight operation at approx. 2000 lux.
Control dial set to (6) =
night-time operation at approx. 2 lux.
The adjusting screw must be turned fully
anti-clockwise when adjusting the detection
zone and performing the function test in
daylight.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel IS 240 DUO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel IS 240 DUO in the language / languages: All languages as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Steinel IS 240 DUO

Steinel IS 240 DUO User Manual - English, German, Polish - 66 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info