592544
8
Zoom out
Zoom in
Previous page
1/66
Next page
1514
y Disconnect the power supply
before attempting any work on
the motion detector.
y During installation, the electric
power cable to be connected must
be voltage-free.Therefore, switch
off the power first and check free-
dom from voltage with a voltage
detector.
y Installing the motion detector in-
volves work on the mains power
supply. This work must therefore be
carried out professionally in accord-
ance with the applicable national
wiring regulations and electrical
operating conditions (
D
- VDE
0100,
A
- ÖVE-EN 1,
- SEV
1000).
Safety instructions
Principle
Lights, alarms, and many other things
triggered by movement - for your con-
venience and safety.
Whether a house door, garage, patio
or carport, stairs, a storeroom or cellar
are involved, this infrared motion de-
tector is rapidly installed and ready for
operation anywhere.
The IS 240 DUO is equipped with two
120° pyro sensors which detect the
invisible heat emitted by moving ob-
jects (pedestrians, animals etc.).
The heat thus detected is electroni-
cally converted and switches ON con-
nected consumers (e.g. a light). No
heat radiation is detected through ob-
stacles, such as walls or glass and no
switching therefore occurs. The two
pyro sensors have a detection angle
of 240° with an opening angle of 180°.
Important: the safest motion detec-
tion is obtained when the device is
mounted and aligned laterally to the
walking direction and no obstacles
(such as trees and walls, for example)
obstruct the view.
Installation instructions
Installation
1) Supply lead
2) Service lead
3) Protective-earth
conductor
4) Lugs for surface-routed
supply lead
y Wall mounting
Warning: installation involves a
mains connection. With 230 V, a
risk of electrocution exists! There-
fore, switch off the power first and
check freedom from voltage with a
voltage tester. Installation of the
sensor involves work on the mains
power supply; this work must
therefore be carried out profession-
ally in accordance with regulations.
Please note that the motion detec-
tor must be protected by a 10 A cir-
cuit breaker.
The installation site should be at
least 50 cm from a light, since the
latter's heat radiation could result in
false triggering of the sensor. The
installation height should be ap-
prox. 2 m.
Unscrew the fastening screw 5
counterclockwise with a screw-
driver, slide down the mounting
plate 1 and remove it. Do not undo
the internal wiring to the terminal
block, but extract the block by
pulling it gently.
Insert the rubber plugs into the
mounting plate. Hold the mounting
plate against the wall and mark the
drill holes (paying attention to the
wiring arrangement in the wall), drill
the holes and insert the dowels.
In order to be able to perform a
switching operation, a power sup-
ply lead with at least two phases
must run to the unit and a second
lead out to the consumer. The two
rubber plugs can be pierced for this
purpose with a screwdriver.
Two lugs are provided on the bot-
tom of the wall fastener for surface
wiring. These can be snapped off
easily. After passing the wiring
through, the mounting plate can
be screwed in place.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel IS 240 DUO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel IS 240 DUO in the language / languages: All languages as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Steinel IS 240 DUO

Steinel IS 240 DUO User Manual - English, German, Polish - 66 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info