593146
9
Zoom out
Zoom in
Previous page
1/72
Next page
16 17
Functions
Once you have connected the
unit to the mains power sup-
ply, closed the housing and
tted the lens, you are ready
to put the system into opera-
tion. Two setting options are
concealed behind the design-
er front trim .
Important: Only select time
and twilight setting with the
lens in place.
Twilight setting (response threshold)
(Factory setting: daylight operation 2000 lux)
The sensor's response threshold can be infi nitely varied from
2 – 2000 lux.
Control dial set to = daylight operation at approx.
2000 lux.
Control dial set to = twilight operation at approx. 2 lux.
To adjust the detection zone in daylight, the control dial must
be set to
(daylight operation).
Switch-OFF delay (time setting)
(factory setting: 5 sec.)
Light ON duration can be infi nitely varied from 5 sec. to
15 min.
Control dial turned fully anticlockwise) = shortest time (5 sec.)
Control dial turned fully clockwise = longest time (15 min.)
When setting the detection zone, it is recommended to select
the shortest time (dial turned fully anticlockwise).
2 – 2000 lux
5 sec. – 15. min.
The corner wall mounts
provided with the unit make it
easy to install the IS 2180-5
on internal and external
corners. Use the corner wall
mount as a template for
drilling holes. This way, you
will drill the hole at the right
angle, allowing you to fi t the
wall mount with ease.
Installing corner wall mount
b) Connecting power supply
lead for load
The power supply lead to
the light is also a 2 - 3-core
cable. Connect the light's
live conductor to the terminal
marked L’. Connect the
neutral conductor to the
terminal marked N together
with the mains power supply
lead's neutral conductor.
Connect the protective-earth
conductor to the earth
terminal ( ).
7. Screw on enclosure and
re-close.
8. Fit sensor lens (reach
either 8 m or 20 m max.),
see section on setting reach.
9. Select time setting
and twilight setting
(see 'Functions').
10. Fit designer front trim
and secure in place with
lock screw to prevent
unauthorised removal.
Important: Reversing the
connections may result in
damage to the unit.
Manual override function
If a mains switch is installed
in the mains supply lead,
the following functions are
provided in addition to simply
switching light ON and OFF:
Important:
The switch should be
actuated in rapid succession
(in the 0.5 –1 sec. range).
Sensor mode
1) Switch light ON:
Switch OFF and ON once.
Light stays on for the period
selected.
2) Switch light OFF:
Switch OFF and ON once.
Light goes out or switches to
sensor mode.
3) Manual override:
Turn switch OFF and ON
twice. The light is set to stay
ON permanently for 4 hours
(LED - below the lens - lights
up) and then automatical-
ly returns to sensor mode
(LED OFF).
Manual override can also be
deactivated during the 4-hour
period by switching OFF and
back ON again. The light then
returns to sensor mode.
1 x OFF/ON
2 x OFF/ON
5 sec. - 15 min.
4 hours
GB
IS 2180-5_85x120_Zentraleuropa.indd 16-17IS 2180-5_85x120_Zentraleuropa.indd 16-17 17.12.13 14:2517.12.13 14:25
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Steinel IS 2180-5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Steinel IS 2180-5 in the language / languages: All languages as an attachment in your email.

The manual is 3,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info