619139
42
Zoom out
Zoom in
Previous page
1/52
Next page
42
1. Turn the treadmill on. Increase treadmill speed to 3.0 mph (5.0 kph).
2. Adjust tracking by adjusting the tailroller Allen screws (located at the back sides of the tailroller) with a 1/4" Allen
wrench in 1/4-turn increments.
If the running belt is tracking to the left, adjust the running belt to track to the right. Tighten the left tailroller
Allen screw by turning clockwise, or loosen the right tailroller bolt by turning counter-clockwise.
If the running belt is tracking to the right, adjust the running belt to track to the left. Tighten the right tailroller
Allen screw by turning clockwise or loosen the left tailroller bolt by turning counter-clockwise.
3. After the running belt appears to be tracking properly, increase the treadmill speed to 10.0 mph (16.0 kph) and
verify that the belt stays centered.
Slipping-Running Belt: Remove the motor shroud and operate the treadmill slowly at 1 to 2 mph (2 to 3 kph). While
observing the headroller, walk on the belt and try to slow it down by gently applying pressure with your feet while holding
the handrails. If only the running belt, and not the headroller, slows down, tighten the running belt by turning both the right
and left tailroller adjustment bolts clockwise 1/4-turn. Repeat this adjustment until the running belt no longer slips,
ensuring that you turn both tailroller bolts an equal number of turns. Re-install the motor shroud. If the headroller and the
running belt both slow down, tighten the drive belt as described under “Slipping-Drive Belt”, below.
Thumping: Turn the treadmill off. Turn the right and left tailroller adjustment bolts counter-clockwise with the M6 Allen
wrench until the running belt is loose. Note the number of times each bolt is turned. Remove excess accumulated running
deck wax from the tailroller with a credit card, a putty knife, or other flexible plastic implement. Tighten the running belt by
turning the adjustment bolts clockwise the same number of turns as they were loosened. Turn the treadmill on and check
for sideward movement and/or slipping of the running belt. Tighten the tailroller adjustment bolts further, if necessary, in
1/4-turn increments.
REWAX BELT
Periodic running belt rewaxing virtually eliminates belt down time, and maximizes the life of the belt. Whenever the present
distance is 2000 miles (or 3000 km) more than the LAST DECK (last deck service), the start-up display will scroll REWAX
BELT. This is a reminder to have your maintenance or service provider perform the 5-minute belt rewaxing procedure at
your convenience. (Immediate service is not required). Wax is included in the treadmill.
TOOLS & MATERIALS
Bottle of Wax Powder (1)
Clean Towel (1)
Paint Stick or Ruler (1)
Diluted All-purpose Cleaner (409), or Bristle Brush
PROCEDURE
Apply wax powder while belt & deck are still warm
(5 minutes minimum use) for optimum benefit.
1. CAUTION: turn treadmill power off and unplug the power cord before rewaxing the belt.
2. CLEAN DECK & BELT:
A. Using the paint stick or ruler, slide a towel under the middle of the belt from one side of the frame to the other.
B. Hold the edges of the towel; pull to the tailroller; pull to the headroller; then pull the belt down to wipe the
remaining belt. TIP: Fold the dirty towel and shake into trash.
3. LIFT BELT: Lift the left side (facing display) of the belt, about 12 inches down from the motor shroud (see figure).
Hold the belt up to elevate the belt from the deck.
4. SPREAD WAX: Flip the nozzle on the cap of the wax bottle. Point the nozzle at the deck. Be sure that the bottle is
tilted at a downward angle. Squeeze the wax bottle twice between the running belt and the deck. TIP: Gently shake
the bottle between each squeeze.
5. Repeat steps 3 and 4, about 18 inches from the end of the deck.
6. Repeat steps 3 through 5, on the right side of the belt/deck.
7. WALK: Plug in the treadmill. Turn the treadmill ON/OFF switch to the ON position. Start the treadmill at 1 mph
and walk on all sections of the belt and deck for 1 minute to ensure the wax has been evenly distributed and
worked-in properly.
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for StarTrac S-TRx Treadmill at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of StarTrac S-TRx Treadmill in the language / languages: English as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info