720594

Stanley STR-4 in 1 Manual

26
Zoom out
Zoom in
Previous page
1/240
Next page
26
5.2 Stop and switch off
Let go of the throttle lever (8).
- Let the engine to return without gas to the idle speed
and let the device to continue to run for 10 to 15
seconds.
- Set the operating switch (3) on the operating handle to
"STOP".
7. Working with the brush cutter / grass
trimmer
- Familiarize yourself - if the device is switched off - first
with the operation and holding, if you are working with
the Petrol- brush cutter work for the first time.
- The Petrol-brush cutter has to be designed in such a
way that they are held by the operator only on the right
side of the body’s side.
- Hold the petrol-brush cutter tight always with both
hands on the handles.
- Hold the operating handle with your right hand and
with the left hand the handle of the hand bar.
- Always make sure that the cutting tool still continues
to rotate for a short time after the throttle is released.
- Always ensure you have a good engine idle speed, so
that the cutting tool does not rotate any more when the
throttle is pressed.
- Work with high speed, and thus you will have the best
cutting results.
- Hold the device with evenly curved movement from left
to right and back again.
Then cut the next length.
Caution: Direct the device always back only again to the
initial position before you cut the next length.
- If you bump into a stone or a tree while working, switch
off the engine and disconnect the spark plug connectors
and inspect the Petrol-brush cutter for damage.
Caution: When working in difficult terrain and slopes,
please be especially careful. In case of high grass, cut
gradually in order not to overload the device. First cut
the tips, work then gradually.
Always wear safety glasses and a hearing protection
and during deforestation work, a protective helmet.
7.1 Mowing with a thread head
- Use the thread cartridge to maintain a clean cut also of
uneven edges, fence posts and trees.
- Guide the trim line carefully past an obstacle and cut
with the thread tip around the obstacle. In case the trim
line comes in contact with rocks, trees and walls, the
thread becomes frayed prematurely or breaks.
- Never replace the plastic thread never by a metal wire
- Risk of injury!
7.2 Mowing with a cutter blade
- Use the cutter blade to thin out scrub, uncontrolled
growth, young stocks of trees (maximum 2 cm trunk
diameter) and tall grass.
- While using the metal cutting tools, there is always the
danger of a backlash, if the tool comes into contact with
a solid obstacle (rocks, trees, branches etc.).
While doing so, the device is thrown back against the
direction of rotation.
- In case of uncontrolled growth and scrub, let the cutter
blad to "dive" from above. Through this, the material to
be cut is chopped.
ATTENTION: Follow the procedures for this work
technology with caution, because the greater the
distance of the cutting tool to the ground, the greater
the risk that the material to be cut and foreign objects
are thrown to the side.
For an adequate protective equipment during the use,
care has to be taken as per the operating instructions.
All other usages are ruled out. The user / operator is
responsible for injuries resulting damage or injury due to
incorrect use.
and not the manufacturer. Only 4-teeth blades suitable
for the machine as mentioned in the operating manual
may be used.
G
B
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STR-4 in 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STR-4 in 1 in the language / languages: English, German, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 9,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info