720755

Stanley STHT77592-1 Manual

12
Zoom out
Zoom in
Previous page
1/238
Next page
12
GB
3.
Mark P1 where the horizontal and vertical beams
cross on the wall.
4.
Turn the laser 180º.
5.
Mark P2 where the horizontal and vertical beams
cross on the wall (Figure
D
2
).
6.
Turn the laser 180º and move it near the rst wall
(Figure
D
3
).
7.
Near P1, mark P3 where the horizontal and
vertical beams cross on the wall.
8.
Turn the laser 180º (Figure
D
4
).
9.
Near P2, mark P4 where the horizontal and
vertical beams cross on the wall.
10.
Measure the vertical distance between P1 and
P3.
11.
Measure the vertical distance between P2 and
P4.
12.
If your measurement is greater than the Allowable
Distance Between P1 & P3 or P2 & P4 for the
corresponding Distance Between Walls in the
following table, the laser must be serviced at an
authorized service center.
Distance
Between Walls
Allowable Distance
Between P1 & P3 or
P2 & P4
30′ (9m) 1/8” (3mm)
40′ (12m) 5/32” (4mm)
50′ (15m) 7/32” (5mm)
Horizontal Beam Accuracy
Checking the horizontal pitch calibration of the
laser requires a single wall at least 30′ (9m) long.
It is important to conduct a calibration check using
a distance no shorter than the distance of the
applications for which the tool will be used.
1.
Place the laser on a tripod facing the corner of
a room (Figure
E
1
).
2.
Move the Power/Transport Lock switch to the
right (Figure
A
3
) to turn the laser ON in
self-leveling mode and display the horizontal and
vertical beams.
3.
Aim the vertical beam at a corner of the room.
4.
Where the horizontal beam crosses the center of
the adjacent wall, mark P1.
5.
Turn the laser so the vertical beam crosses P1
(Figure
E
2
).
6.
Where the horizontal beam crosses the vertical
beam, mark P2.
7.
Turn the laser so the vertical beam is aimed at
the second corner (Figure
E
3
).
8.
Where the horizontal beam is vertically in line
with P1 and P2, mark P3.
9.
Measure the vertical distance between the
highest and lowest points (between P1, P2, and/
or P3).
10.
If your measurement is greater than the Allowable
Distance Between Highest & Lowest Points for
the corresponding Distance Between Walls in the
following table, the laser must be serviced at an
authorized service center.
Distance Between
Walls
Allowable Distance
Between Highest &
Lowest Points
30′ (9m) 1/4” (6mm)
40′ (12m) 5/16” (8mm)
50′ (15m) 13/32” (10mm)
Vertical Beam Accuracy
Checking the vertical (plumb) calibration of the
laser can be most accurately done when there is
a substantial amount of vertical height available,
ideally 30′ (9m), with one person on the oor
positioning the laser and another person near a ceiling
to mark the position of the beam. It is important to
conduct a calibration check using a distance no
shorter than the distance of the applications for which
the tool will be used.
1.
Place the laser at least 3.28 ft (1.0m) from a door
jamb (Figure
F
1
).
2.
Move the Power/Transport Lock switch to the
right (Figure
A
3
) to turn the laser ON in
self-leveling mode and display the horizontal and
vertical beams.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHT77592-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT77592-1 in the language / languages: All languages as an attachment in your email.

The manual is 7,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info