720755

Stanley STHT77592-1 Manual

11
Zoom out
Zoom in
Previous page
1/238
Next page
11
GB
Installing AA Batteries
Load new AA batteries in the STHT77502-1 or
STHT77592-1 laser.
1.
Turn the laser upside down.
2.
On the bottom of the laser, lift up the latch to
open the battery compartment cover
(Figure
B
1
).
3.
Insert two new, high-quality, name brand AA
batteries, making sure to position the - and +
ends of each battery as noted inside the battery
compartment (Figure
B
2
).
4.
Push the battery compartment cover closed until
it snaps in place (Figure
B
3
).
When the laser is not in use, keep the Power/
Transport Lock switch in the center (OFF) position
(Figure
A
2
) to save battery power.
Turning the Laser On
1.
Place the laser on a smooth, flat, level surface,
with the laser facing straight ahead toward the
opposing wall (0º position).
2.
Turn the laser ON to display the front cross
beams. Either:
• Move the Power/Transport Lock switch to the
left to keep the pendulum locked and display
the cross beams in manual mode
(Figure
A
1
).
• Move the Power/Transport Lock switch to the
right to unlock the pendulum and display the
cross beams in self-leveling mode
(Figure
A
3
).
3.
Press (Figure
A
4
) once to display
a horizontal laser line, a second time to display
a vertical line, and a third time to display
a horizontal line and a vertical line.
4.
Check the laser beams.
• If the laser is tilted so much that it cannot self-
level (> 4°), or the laser is not level in manual
mode, the laser beams will flash.
• If the laser beams ash, the laser is not level
(or plumb) and should NOT BE USED for
determining or marking level or plumb. Try
repositioning the laser on a level surface.
5.
If ANY of the following statements are TRUE,
continue with the instructions for Checking Laser
Accuracy BEFORE USING THE LASER for
a project.
• This is the first time you are using the laser
(in case the laser was exposed to extreme
temperatures).
• The laser has not been checked for accuracy
in a while.
• The laser may have been dropped.
Checking Laser Accuracy
The laser tools are sealed and calibrated at the factory.
It is recommended that you perform an accuracy
check prior to using the laser for the rst time (in
case the laser was exposed to extreme temperatures)
and then regularly to ensure the accuracy of your
work. When performing any of the accuracy checks
listed in this manual, follow these guidelines:
• Use the largest area/distance possible, closest
to the operating distance. The greater the area/
distance, the easier to measure the accuracy of
the laser.
• Place the laser on a smooth, at, stable surface
that is level in both directions.
• Mark the center of the laser beam.
Level Beam Accuracy
Checking the horizontal scan calibration of the laser
requires two walls 30′ (9m) apart. It is important
to conduct a calibration check using a distance no
shorter than the distance of the applications for which
the tool will be used.
1.
Place the laser on a tripod facing straight ahead
toward a wall (Figure
D
1
).
2.
Move the Power/Transport Lock switch to the
right (Figure
A
3
) to turn the laser ON in
self-leveling mode and display the horizontal and
vertical beams.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHT77592-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT77592-1 in the language / languages: All languages as an attachment in your email.

The manual is 7,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info