720754

Stanley STHT77502-1 Manual

14
Zoom out
Zoom in
Previous page
1/238
Next page
14
GB
Using the Laser with the Bracket
A bracket (Figure
H
) is included with the laser so
you can easily attach the laser to a stud, ceiling grid,
or pole.
1.
Securely attach the laser to the bracket.
• Using the 1/4-20 thread on the bottom, side,
or back of the laser (Figure
C
), position the
laser on the 1/4-20 thread on the bracket arm
(Figure
H
1
).
• Turn the laser knob (Figure
H
2
) clockwise
to lock the laser on the 1/4-20 thread on the
bracket arm.
2.
If needed, change the height or position of the
laser on the bracket.
• Turn the adjustment knob (Figure
H
3
)
counter-clockwise to loosen the bracket arm.
• Slide the bracket arm up or down to the desired
height (Figure
H
4
). To change the bracket
from 90° to 180°, slide the bracket arm to the
top of the bracket and then flip the arm to the
right (Figure
H
5
).
• Turn the adjustment knob (Figure
H
3
)
clockwise to lock the bracket arm in place.
3.
Use the bracket’s clamp (Figure
H
6
) to hold
the laser in place on a stud, ceiling grid, or pole.
• If necessary, rotate the clamp so it is positioned
at the correct angle for attaching to the object.
While holding the bracket arm with one hand,
use your other hand to turn the clamp
(Figure
H
7
).
• Position the bracket’s clamp around the stud,
ceiling grid, or pole.
• Turn the clamp knob (Figure
H
8
) clockwise
until the clamp is tight around the object and
the bracket is held in place.
Using the Laser with Other
Accessories
WARNING:
Since accessories other than those offered
by STANLEY have not been tested with this
laser, use of such accessories with this laser
could be hazardous.
Only use STANLEY
®
accessories that are
recommended for use with this model. Accessories
that may be suitable for one laser may create a risk of
injury when used with another laser.
The laser is equipped with a 1/4-20 female thread on
the bottom, side, and back (Figure
C
)
to accommodate current or future STANLEY
®
accessories.
Other recommended accessories for use with this
laser are available at extra cost from your local dealer
or authorized service center. If you need assistance
locating any accessory, please contact your nearest
STANLEY service center or visit our website:
http://www.STANLEY.com.
Maintenance
• When the laser is not in use, clean the exterior parts
with a damp cloth, wipe the laser with a soft dry
cloth to make sure it is dry, and then store the laser
in the kit box provided.
• Although the laser exterior is solvent resistant,
NEVER use solvents to clean the laser.
• Do not store the laser at temperatures below -5 ˚F
(-20 ˚C) or above 140 ˚F (60 ˚C).
• To maintain the accuracy of your work, check the
laser often to make sure it is properly calibrated.
• Calibration checks and other maintenance repairs
may be performed by STANLEY service centers.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHT77502-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT77502-1 in the language / languages: All languages as an attachment in your email.

The manual is 7,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info