720754

Stanley STHT77502-1 Manual

13
Zoom out
Zoom in
Previous page
1/238
Next page
13
GB
3.
Aim the vertical laser beam toward the door jamb.
4.
Along the bottom of the laser beam, mark three
locations
a
,
b
, and
c
; where
b
is midway
between
a
and
c
.
5.
Where the top of the laser beam appears at the
top of the door jamb, mark
e
.
6.
Move the laser to the opposite side of the door
jamb (Figure
F
2
).
7.
Align the bottom of the laser beam with
a
,
b
,
and
c
.
8.
Where the top of the laser beam appears at the
top of the door jamb, mark
f
.
9.
Measure the distance between
e
and
f
.
10.
If your measurement is greater than the
Allowable Distance Between
e
and
f
for the
corresponding Ceiling Height
D
in the following
table, the laser must be serviced at an authorized
service center.
Ceiling Height
D
Allowable Distance
Between
e
and
f
6.56′ (2.0m) 1/16" (1.5mm)
8.20′ (2.5m) 3/32” (2.0mm)
9.84′ (3.0m) 1/8” (2.5mm)
Side Vertical Beam Accuracy
Checking the vertical (plumb) calibration of the side
laser can be most accurately done when there is at
least 16ft. (1.5m) of oor space and another person
to assist. It is important to conduct a calibration check
using a distance no shorter than the distance of the
applications for which the tool will be used.
1.
Place the laser on a level oor that is at least
16ft. (1.5m) long.
2.
Move the Power/Transport Lock switch to the
right (Figure
A
3
) to turn the laser ON in
self-leveling mode and display the horizontal and
vertical beams.
3.
Press once to display the side vertical beam.
4.
Measure exactly 3 ft. (0.91m) from the center of
the laser unit along the front vertical beam, and
mark P1 (Figure
G
1
).
5.
Measure exactly 4 ft. (1.22m) out from the center
of the laser unit along the side vertical beam, and
mark P2 (Figure
G
2
).
6.
Measure the distance between P1 and P2
(Figure
G
3
).
7.
If the distance between P1 and P2 is not 5ft
+ 1/32” (1.522m + 0.75mm), please bring the
laser unit to your nearest STANLEY service
center for calibration.
Using the Laser
Operating Tips
• Always mark the center of the beam created by
the laser.
• Extreme temperature changes may cause
movement of internal parts that can affect accuracy.
Check your accuracy often while working.
• If the laser is ever dropped, check to make sure it
is still calibrated.
• As long as the laser is properly calibrated, the
laser is self-leveling. Each laser is calibrated at
the factory to nd level as long as it is positioned
on a at surface within average ± 4° of level. No
manual adjustments are required.
• Use the laser on a smooth, at, level, surface.
Turning the Laser Off
Slide the Power/Transport Lock switch to the OFF
position (Figure
A
2
) when the laser is not in use. If
the switch is not placed in the OFF position, the laser
will not turn off.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHT77502-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT77502-1 in the language / languages: All languages as an attachment in your email.

The manual is 7,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info