720751

Stanley STHT1-77341 Manual

14
Zoom out
Zoom in
Previous page
1/210
Next page
14
STHT77341
Horizontal Beam Accuracy (See figure
I
)
•
I
1
Place laser tool as shown with laser ON. Aim vertical
beam towards the first corner or a set reference point.
Measure out half of the distance D
1
and mark point P
1
.
•
I
2
Rotate laser tool and align front vertical laser beam
with point P
1
. Mark point P
2
where the horizontal and
vertical laser beams cross.
•
I
3
Rotate laser tool and aim vertical beam towards the
second corner or set reference point. Mark point P
3
so
that it is vertically in line with points P
1
and P
2
.
•
I
4
Measure the vertical distance D
2
between the
highest and lowest point.
• Calculate the maximum offset distance and compare
to D2 .
• If D
2
is not less than or equal to the calculated
maximum offset distance the tool must be returned
to your Stanley Distributor for calibration.
Maximum Offset Distance:
= 0,5
mm
m
x D
1
m
Maximum
= 0,05
in
ft
x D
1
ft
Compare: (See figure
I
4
)
D
2
≤ Maximum
Example:
• D
1
= 5 m, D
2
= 1,0 mm
• 0.5
mm
m
x 5 m = 2.5mm
(maximum offset distance)
• 1.0 mm ≤ 2.5mm
(TRUE, tool is within calibration)
Level Beam Accuracy (See figure
H
)
•
H
1
Place laser tool as shown with laser ON. Mark point
P
1
at cross.
•
H
2
Rotate laser tool 180° and mark point P
2
at cross.
•
H
3
Move laser tool close to wall and mark point P
3
at cross.
•
H
4
Rotate laser tool 180° and mark point P
4
at cross.
•
H
5
Measure the vertical distance between P
1
and P
3
to get D
3
and the vertical distance between P
2
and P
4
to get D
4
.
• Calculate the maximum offset distance and compare to
the difference of D
3
and D
4
as shown in the equation.
• If the sum is not less than or equal to the
calculated maximum offset distance the tool
must be returned to your Stanley Distributor for
calibration.
Maximum Offset Distance:
= 0,5
mm
m
x (D
1
m - (2 x D
2
m))
Maximum
= 0,05
in
ft
x (D
1
ft - (2 x D
2
ft))
Compare : (See figure
H
5
)
D
3
- D
4
≤ ± Maximum
Example:
• D
1
= 10 m, D
2
= 0,5 m
• D
3
= 0,5 mm
• D
4
= - 1,0 mm
• 0,5
mm
m
x (10 m - (2 x 0,5 m) = 4.5mm
(maximum offset distance)
• (0,5 mm) - (- 1,0 mm) = 1,5 mm
• 1,5 mm ≤ 4.5 mm
(TRUE, tool is within calibration)
Cross90 GB_STHT77341.indd 14 01/07/2013 09:50
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHT1-77341 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT1-77341 in the language / languages: All languages as an attachment in your email.

The manual is 3,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info