622189

Stanley STHT1-12184 -APC-BN Manual

9
Zoom out
Zoom in
Previous page
1/130
Next page
TECHNICAL DATA:
Please look at the technical table marked * at the end of this manual.
PROBLEM CAUSE CORRECTION
Failure to cycle Air supply restriction Check air supply equipment
Tool dry, lack of lubrication Use STANLEY BOSTITCH Air Tool Lubricant
Worn head valve O-rings (if present) Replace O-rings
Broken cylinder cap spring Replace cylinder cap spring
Head valve (if present) stuck in cap Disassemble/Check/Lubricate
Lack of power; slow to cycle Air pressure too low Check air supply equipment
Tool dry, lacks lubrication Use STANLEY BOSTITCH Air Tool Lubricant
Broken cylinder cap spring Replace cylinder cap spring
O-rings/seals cut or cracked Replace O-rings/seals
Exhaust blocked Check bumper, head valve spring, muffler
Trigger assembly worn/leaks Replace trigger assembly
Cylinder sleeve not seated correctly on bottom bumper Disassemble to correct
Head valve dry Disassemble/lubricate
Trigger valve housing leaking air. O-ring cut or cracked Replace O-ring
Trigger valve stem leaks air O-rings/seals cut or cracked Replace O-rings/seals
Frame/nose leaks air O-ring or gasket is cut or cracked Replace O-ring or gasket
Bumper cracked/worn Replace bumper
Frame/cap leaks air Damaged gasket or seal Replace gasket or seal
Cracked/worn head valve bumper Replace bumper
Loose cap screws Tighten and recheck
Skipping fasteners; intermittent feed Worn bumper Replace bumper
Air restriction/inadequate air flow through quick
disconnect socket and plug
Replace quick disconnect fittings
Worn piston O-ring (if present) Replace O-ring, check driver
Tool dry, lacks lubrication Use STANLEY BOSTITCH Air Tool Lubricant
Damaged pusher spring Replace spring
Low air pressure Check air supply system to tool
Loose magazine nose screws Tighten all screws
Fasteners too short for tool Use only recommended fasteners
Bent fasteners Discontinue using these fasteners
Wrong size fasteners Use only recommended fasteners
Leaking head cap gasket Tighten screws/replace gasket
Trigger valve O-ring cut/worn Replace O-ring
Broken/chipped driver Replace driver (check piston O-ring)
Dry/dirty magazine Clean/lubricate use STANLEY BOSTITCH Air Tool Lubricant
Worn magazine Replace magazine
Fasteners jam in tool Driver channel worn Replace nose/check door
Wrong size fasteners Use only recommended fasteners
Bent fasteners Discontinue using these fasteners
Loose magazine/nose screws Tighten all screws
Broken/chipped driver Replace driver (check piston O-ring)
A Length mm. K Air consumption per shot @ 5.6 Bar
B Height mm. L Activation type
C Width mm. M Summer lubricant
D Weight Kg. N Winter lubricant
E Noise Lpa, 1s, d O O-ring lubricant
F Noise Lwa, 1s, d P Fastener Name
G Noise Lpa, 1s, 1m Q Dimensions mm.
H Vibration m/s
2
R Head/crown
I P max Bar S Magazine capacity
J P min Bar T New Driver Length mm.
U Max. Depth Inside Piston mm.
TROUBLESHOOTING
l Disconnect the tool from the air supply and empty the magazine completely before proceeding.
l If the problem cannot be resolved using the guide below, Contact your nearest Stanley representative or distributor.
FT72124-a-0611_Tool_Manual_AW.indd 9 05/07/2011 17:01
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHT1-12184 -APC-BN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT1-12184 -APC-BN in the language / languages: All languages as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info