622189

Stanley STHT1-12184 -APC-BN Manual

8
Zoom out
Zoom in
Previous page
1/130
Next page
IN ADDITION TO THE OTHER WARNINGS IN THIS MANUAL
OBSERVE THE FOLLOWING FOR SAFE OPERATION:
l Respect your Stanley pneumatic fastening tool as a tool. It
is not a toy. No Horseplay.
l Use the Stanley pneumatic tool only for the purpose for
which it was designed.
l Never use the tool in a manner that could cause a
fastener to be directed towards the user or others in the
work area.
l Do not use the tool as a hammer.
l Always carry the tool by the handle. Never carry the
tool by the air hose. Never carry the tool with the trigger
pulled.
l Do not alter or modify this tool from the original design or
function without the written approval of Stanley Inc.
l Always be aware that misuse and improper handling of this
tool can cause injury to yourself and others.
l Never clamp or tape the trigger or safety trip in an
actuated position.
l Never leave a tool unattended with the air hose attached.
l Do not operate this tool if it does not contain a legible
WARNING LABEL.
l Do not continue to use a tool that leaks air or does not
function properly. Notify your nearest Stanley stockist if
your tool continues to experience functional problems.
l During operation, hold the tool in such a way that no
injuries can be caused to the head or to the body should
the tool recoil increase due to a drop in the supply air
pressure or hard areas within the work piece.
l Do not work close to corners or at the edge of the work
piece. The fastener could slip out of the work piece,
possibly causing injury.
l When transporting the tool, disconnect the air supply first.
l Check that the safety trip (if present) and the trigger both
function correctly.
l Do not dismantle or block any part of the tool, in particular
not the safety trip.
l Never perform “emergency repairs” without the proper
equipment.
l Avoid weakening the tool by punching or engraving.
MAINTENANCE
Disconnect the tool from the air supply and completely empty
the magazine before starting maintenance or repairs. Note the
warnings in this manual in the Tool Technical Data and on the
tool itself and use extra care when evaluating problem tools.
Stanley replacement parts are recommended. Do not use
modified parts or parts that will not give performance equal to
the original equipment.
When repairing a tool, make sure the internal parts are
clean and lubricated. Use Parker “O”-Lube or equivalent
on all “O”-rings. Coat each “O”-ring with “O”-Lube before
assembling. Use a small amount of oil on all moving surfaces
and pivots.
NOISE EMISSION (See Tool Technical Data)
The characteristic noise values for the tool have been
determined in accordance with EN 12549 - “Acoustics - Noise
test code for fastener driving tools - Engineering Method.”
These values are tool related characteristic values and do not
represent the noise development at the point of use.
INFORMATION ON VIBRATION (see Tool Technical Data)
The characteristic vibration value for the tool has
been determined in accordance with ISO/WD 8662-11
“Measurement of vibration in hand held power tools - Part 11
Fastener Driving Tools”.
This value is a tool related characteristic and does not
represent the influence on the hand-arm system when using
the tool.
FT72124-a-0611_Tool_Manual_AW.indd 8 05/07/2011 17:01
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stanley STHT1-12184 -APC-BN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stanley STHT1-12184 -APC-BN in the language / languages: All languages as an attachment in your email.

The manual is 3,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info